Knoll Systems US-STEREO SENDER warranty Stereo Balun Specifications, Warranty, Features

Stereo Balun Specifications:

Models and Dimensions:

UDR-Stereo (in-wall Decora™ version): 4.1"h x 1.4" w x 2.0"d.

UDS-Stereo (in-wall Decora™ version): 4.1"h x 1.4" w x 2.0"d.

UR-Stereo (black enclosure): 1.1"h x 2.6"w x 2.8"d (28 x 66 x 71 mm).

US-Stereo (black enclosure): 1.1"h x 2.6"w x 2.8"d (28 x 66 x 71 mm).

Input and Outputs:

Send Unit: two stereo input RCA jacks, one 3.5mm mono infrared emitter jack, one RJ-45 out-jack, one-DC power input. Receive Unit: Three RCA output jacks, one RJ-45 in-jack, one- DC power input.

Audio Input Impedance:

Receive Unit: 20k ohms, max 3 Vp-p.

Frequency Response: 10Hz-50kHz +/- 3 dB

Power:

Send Unit: 12 VDC unregulated (one PS1202 will power one each send and receive).

Receive Unit: 12 VDC unregulated (one PS1202 will power one each send and receive).

Infrared:

Send Unit: One stereo 3.5mm jack to connect one single or one dual emitter.

Receive Unit: One triple 3.5 mm jack to connect a three wire Knoll or other infrared receiver. Supplies 12 VDC power for infrared receiver without requiring another power supply.

Warranty

Knoll Systems warrants balun products sold in the USA and Canada by authorized Knoll dealers to be free of defects in materials and workmanship. This warranty extends for three full years from the date of purchase by the original consumer. Any products returned to Knoll Systems and found to be defective by Knoll Systems within the warranty period will be repaired or replaced at Knoll System’s option, at no charge. Knoll Systems will not be responsible for the actual cost of installation or removal of the product, nor for any incidental or consequential damages. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights. You may have additional legal rights that vary from state to state.

Knoll Systems www.knollsystems.com

145 Tyee Drive Point Roberts, WA 98281

12140 Horseshoe Way, Richmond BC V7A 4V4 tel (604) 272 4555, fax (604) 272 5595

UDR-Stereo Receiver

UDS-Stereo Sender

UR-Stereo Receiver

US-Stereo Sender

Installation Instructions v1.1

Warning: To be installed and/or used in accordance with appropriate electrical codes and regulations. If you are not sure about any part of these instructions, consult a qualified electrician.

Caution: Do not install this product in an electrical junction box with 110V or higher unless an approved barrier separates the high and low voltage sections.

Introduction: Thank you for your purchase of a Knoll active balun system. This system is specifically designed to send a stereo line level and an infrared signal safely down a cat 5 or cat 5e wire up to 1000 feet without encountering noise problems. Balun is an acronym for:

BALance – UNbalance

The send module takes a conventional stereo line level signal and balances it (signal is not tied to a ground reference) then sends it via cat 5 to the receive module (with power from the send module). The receive module unbalances the stereo signal back to its former state. This process does not allow any stray magnetism of any sort to contaminate the signal while it is being transported.

Features:

•Tabletop box design or Decora™ style available.

•Safely sends stereo signals up to 1000’ (300 m).

•Sends infrared signal from receiver back to sender.

•PS1202 power supply required on send side only.

Made in Canada Knoll Systems All Rights Reserved • Mix and match tabletop and decora style.