Korg music workstation/sampler

101

8Input the open hi-hat (Tone03).

Set “Step No.” to 04, and press the [3] key. Then set

“Step No.” to 08, and press the [3] key.

If “Fixed Note Mode” is set to Trigger All Tones, play-

ing a single note on the keyboard will cause the rhythm

pattern to play.

If “Fixed Note Mode” is set to Trigger As Played, play-

ing a single note on the keyboard will cause only the

kick (Tone00) to play.

Playing two notes on the keyboard will cause only the

kick (Tone00) and snare (Tone01) to play. In this way,

the number of keys that you play will be played by the

same number of tones.

9Set the parameters for each step.

Use “Velocity” etc. to add accents to the rhythm pat-

tern.

The “Gate” and “Velocity” settings you make here

will be valid if the “Gate” and “Velocity” parameters

(Program P7: Edit-Arpeggiator, Arpeg. Setup page) of

the program selected in Program mode are set to

Step. If these parameters have a setting other than

Step, the “Gate” and “Velocity” that were speciﬁed

for each individual step will be ignored, and the notes

of the arpeggio will be sounded according to the set-

tings of the Program P7: Edit-Arpeggiator, Arpeg.

Setup page. Check the settings of the program.

Set the “Gate” and “Velocity” by using the ARPEG-

GIATOR [GATE] and [VELOCITY] knobs to the cen-

ter position (12 o’clock).

Dual arpeggiator editing

Here we will use a combination as an example in our

explanation.

The same procedure applies when editing an arpeggio

pattern in Sequencer and Song Play modes.

If you have entered this mode from the Combination

mode, the arpeggio pattern selected by the combination

will be affected by your editing.

1In Combination mode, select a combination that uses

the arpeggio pattern you wish to edit.

For this example, select a combination to which both

arpeggiators A and B are assigned.

2Press the ARPEGGIATOR [ON/OFF] key to turn on

the arpeggiator (the key will light).

Even if the arpeggiator had been turned off when you

moved here, you can use the ARPEGGIATOR [ON/

OFF] key to turn it on. However, if “Arpeggiator Run”

A or B are not checked, and if “Arpeggiator Assign,” is

set to off, then the arpeggiator will not operate.

3Select the Global P6: User Arpeggio, Pattern Setup

page.

4If you moved here from Combination mode, use the

“Arpeggio Select” A and B to select the arpeggiator

that you wish to edit.

If this is A, your editing will apply to the parameters

and user arpeggio pattern of arpeggiator A.

If this is B, your editing will apply to the parameters

and user arpeggio pattern of arpeggiator B.

5Switch between arpeggiators A and B, and edit their

respective user arpeggio patterns.

If you wish to stop one of the arpeggiators, return to

Combination mode, and in Combination P0: Play,

select the Arpeggio Play A or the Arpeggio Play B page

and uncheck the “Arpeggiator Run” check box.

6To modify the name of a user arpeggio pattern, use

the Utility “Rename Arpeggio Pattern.” (☞p.115)

7If you wish to save the edited user arpeggio pattern

in internal memory, you must write the user arpeggio

pattern.

In this case, both user arpeggio patterns will be written

simultaneously. If you turn off the power without writ-

ing, the edited contents will be lost (☞p.116).

8If you wish to save the state of the combination at the

same time, return to Combination mode and write

the combination. (☞p.114)

When editing a user arpeggio pattern, pay attention

to the global MIDI channel, the channel of each track,

and the arpeggiator assignments, and make sure that

the arpeggiator you are hearing is the pattern that

you wish to edit.

If you moved here from Sampling mode, the arpeg-

giator will not turn on. Nor will it be possible to edit

arpeggio patterns.

Program

Combination

SequencerSamplingSong PlayGlobalEffectMedia, etcPresetOther