Model
Atomic Digital Wall Clock
With Time with Seconds, Month, Date, Day, & IN/OUT
Temperature
QUICK SETUP GUIDE
Table of Contents
Table of Contents | 1 | ||
Congratulations | 2 | ||
Features: |
| 2 | |
Setup Information: | 2 | ||
The Outdoor Temperature Sensor | 2 | ||
Positioning the Temperature Sensor: | 3 | ||
To wall mount the Temperature Sensor: | 3 | ||
WWVB (Atomic Time) Radio signal: | 3 | ||
Setup of Time and Display Options: | 3 | ||
1. | Set the Time Zone: | 4 | |
2. | Set Daylight Saving Time ON/OFF: | 4 | |
3. | Set Language: | 4 | |
5. | Set Time Manually - Minute: | 4 | |
6. | Set Date Manually - Year: | 4 | |
7. | Set Date Manually - Month: | 4 | |
8. | Set Date Manually - Date: | 4 | |
9. | Set Date Manually - Day of Week: | 4 | |
10. Set 12 or 24 Hour Time Mode: | 4 | ||
11. Set Temperature Mode - °F or °C: | 4 | ||
Daylight Saving Time | 4 | ||
Setting the Daily Alarms: | 4 | ||
About the Daily Alarms: | 5 | ||
Automatic Snooze function: | 5 | ||
Online Resources | Error! Bookmark not defined. | ||
Care and Maintenance | Error! Bookmark not defined. | ||
Battery Replacement | 5 | ||
The Low Battery Icons: | 5 | ||
Specifications | 5 | ||
Power Requirements | 6 | ||
FCC Statement | 6 | ||
Warranty Information | 6 | ||
Page 1 of 6
Congratulations
You have purchased an atomic digital Atomic Clock from La Crosse Technology®, providing the world's most accurate time at a glance, plus wireless outdoor temperature.
This product offers: INSTANT TRANSMISSION is the 
transmitters: follow your climatic variations in
Features:
WWVB Radio Controlled Clock (Atomic Clock)
Time in 12/24 hour format
Manual time setting option
Time Zone setting: +/- 12 Hours from GMT
Daylight Saving Time(DST) On/Off
Continuous calendar up to year 2054
Date and weekday displayed and set automatically with the time
Temperature display in °F or °C
Snooze function (10 minutes)
Indoor thermometer
Wireless Outdoor Temperature Sensor
Low battery icons for display and sensor
Setup Information:
The Temperature Sensor uses 2 x AAA, IEC LR3 1.5V battery. To install and replace the batteries, please follow the steps that follow:
Position the Atomic Clock and the Outdoor Sensor five to six feet apart with nothing between them.
Insert batteries into the Wireless Outdoor
Temperature Sensor first - it is important that you do not insert the batteries into the Atomic Clock yet.
You must insert the batteries into the Atomic Clock within 3 minutes of inserting the batteries into the Sensor.
Slide out the battery compartment lid at the bottom of the Outdoor Sensor.
Insert the batteries into the Outdoor Sensor first, observing the correct polarity (see markings inside battery compartment). Replace the battery holder on the unit.
Immediately after and within 3 minutes, insert the batteries into the Atomic Clock, observing the correct polarity (see markings inside battery compartment). Replace the battery cover. The Atomic Clock uses 2 x AA batteries ( IEC LR6, 1.5V ).
The outdoor temperature and the signal reception icon 
should be displayed on the Atomic Clock. If this does not happen after 3 minutes, the batteries will need to be removed from both units and re- inserted, following the instructions above.
Note: In the event of changing batteries in any of the units, all units need to be reset by following the setting up procedures. This is because a random security code is assigned by the Sensor at
Note: If the signal reception is not successful on the first frequency (915MHz) for 22 seconds, the frequency is changed to 920MHz and the learning is tried another 22 seconds. If still not successful the reception is tried for 22 seconds on 910MHz. This will also be done for re- synchronization.
The Outdoor Temperature Sensor
Remote transmission of outdoor temperature to Temperature Station by 915 MHz
Shower proof casing
Page 2 of 6
