Lasko 2515 Armado, Operation, REMOTE CONTROL Figure, Maintenance, Vista des de Arriba, Modelo

MODELO 2515

MODEL 2515

ARMADO

1.Para facilitar el armado, recueste el Ventilador de modo que la parrilla negra y el tablero de control den hacia arriba.

2.Localice el Cable Eléctrico en la parte inferior del Ventilador. Coloque el Cable Eléctrico en los Canales Para Cable de los Soportes De Columna. Encaje firmemente los Soportes De Columna el uno con el otro de modo de formar un Conjunto De Soportes De Columna. (Figura 1)

3.Una el Conjunto De Soportes De Columna a la Base Del Motor con (4) Tornillos M5 de 1/2”de largo. Cerciórese de alinear la Llave del Conjunto De Soportes De Columna con la Muesca Localizadora de la Base Del Motor. (Figura 1)

Conjunto De Soportes De Columna
Tornillos	Base Del
M5 de 1/2”	Motor
Soportes
De Columna
Canales
Para Cable	Muesca
	Localizadora
Cable	Llave
Eléctrico
	Soportes
	De Columna
	Figura 1

4.Arme las Bases de Soporte, introduciendo las Copas en la Base de Soporte A en los Orificios De Copas de la Base de Soporte B. Pase el Cable de Electricidad por el orificio grande en el centro del Conjunto de la Base de Soporte. (Figura 2)

Conjunto de la Base de Soporte -

Vista des de Arriba

Cable

Eléctrico

5.Fije los Tornillos (2) #8 X 1/2” en los cuatro orificios que se encuentran en la parte inferior de la base. (Figura 3)

Conjunto de la Base de Soporte -

Vista des de Abajo

Conjunto

de la Base de Soporte

#8 X 1/2”

Tornillos

Cable

Eléctrico

Figura 3

6.Alinee el Conjunto de la Base de Soporte con el Soporte de Columna, cerciorándose de que el canal del cable en la parte inferior de la base de soporte esté or ientado hacia la parte posterior del Ventilador. Ensamble el Conjunto de la Base de Soporte con el Conjunto del Soporte de Columna utilizando los Tornillos M5 de (4) 1” de largo. Jale con cuidado toda holgura excesiva del Cable de Electricidad e introdúzcala por el Canal Conductor de Cable. (Figura 4)

Conjunto de Columna Para la Base
	Conjunto De
	Soportes De
	Columna
Conjunto	Cable
de la Base
de Soporte	Eléctrico

OPERATION

This Fan may be operated by the Manual Controls located on top of the unit (as shown in Figure 5) or by the Remote Control (shown in Figure 6).

1.Remove the Fan from the carton and assemble as instructed.

2.Place the Fan on a firm, level surface.

WARNING: Plastic or rubber tabs, like the feet on this unit, may stick to hardwood floors. The unit may leave a residue that could darken, stain or leave permanent blemishes on the finish of certain hardwood floors.

3.Plug the power supply cord into a 120 V~ electrical outlet. Be sure plug fits tightly in outlet.

4.When the Fan is plugged in, there will be a “beep” to indicate there is power to the unit.

5.Turn the Fan ON by pressing the Power Button (). The Fan will “beep” twice to indicate that the unit has been turned ON.

6.SPEEDS: Press the Fan Speed Button () to desired speed setting. Each time the Fan Speed Button is pressed, the speed will change from Low (1), to Medium (2), to High (3). When intially plugged in, the Fan will be in Low Speed. When the Fan is turned OFF and ON again, the unit will resume the speed at which it was turned OFF.

7.OSCILLATION: Press the Oscillation Button () to start and stop the oscillation function.

8.TIMER: The timer function allows the unit to be set to operate for a length of time from 1/2 hour to 7 1/2 hours, in increments of a 1/2 hour. Press the Timer Button () to set the length of time desired. Each time the timer button is pressed, the time is increased by 1/2 hour. After reaching 7 1/2 hours, pressing the timer button once more will reset the Fan to continuous running. The lights on the front of the unit will light up appropriately with the length of time that the Fan is set for.

9.SLEEP: This function allows the unit to be set in Sleep Mode. Pressing the Sleep Button () once will set the unit on Low for 6 continuous hours. Pressing the Sleep Button () a second time will reset the unit to 6 continuous hours. The Oscillation Button () will function when the Fan is in Sleep Mode. Pressing any other button (Timer, Fan Speed or the Power Button) will shut off the Sleep Mode.

10.To turn the Fan OFF, press the Power Button () and unplug the unit from the electrical outlet.

REMOTE CONTROL (Figure 6)

1.Install the two “AAA” batteries supplied as shown inFigure 6.

2.The Remote Control Power Button is labeled as ().

3.All the functions performed with the Remote Control work identically to the Manual Controls.

Back of

Remote

Front of

Remote

Figure 6

If you lose your remote control, please call Customer Service to order a replacement at 1-800-233-0268, Monday through Friday, between the hours of 8:00 a.m. and 5:00 p.m. EST.

MAINTENANCE

WARNING: ALWAYS UNPLUG THE CORD BEFORE MOVING OR SERVICING.WARNING: DO NOT IMMERSE FAN IN WATER!

CLEANING: Clean the Fan with the vacuum brush attachment on your vacuum cleaner. This will remove dirt and lint that may accumulate over time. DO NOT ATTEMPT TO TAKE APART FAN. Clean the body of the Fan with a soft cloth.

CAUTION: Do not use gasoline, benzine, thinner, harsh clean- ers, etc. as they may damage the Fan. NEVER use ALCOHOL OR SOLVENTS.

SERVICING: All other servicing, with the exception of general user maintenance, should be performed by an authorized service repre- sentative. Call 1-800-233-0268, Monday through Friday, between the hours of 8:00 a.m. and 5:00 p.m. EST for the location of your nearest service center.

Base de

Soporte A

Base de	Copas
Soporte B

Figura 2

Rev. C 9/04

		Canal
		Conductor
		de Cable
	M5 X 1”
	Tornillos	Figura 4
6		2515ES

STORAGE: Store the Fan, with these instructions, in a cool, dry place.

Remote Storage

Figure 5

Rev. C 9/04 3 2515ES