MODEL 2530
MODELO 2530
OPERATION
This Fan may be operated by the Manual Controls located on top of the unit (as shown in Figure 5) or by the Remote Control (shown in Figure 6).
1. Place the Fan on a firm and level surface.
CAUTION: Plastic or rubber tabs, like the feet on this unit, may stick to furniture surfaces and/or hardwood floors.The unit may leave a residue that could darken, stain or leave permanent blemishes on the finish of certain furniture surfaces, including wood surfaces, and/or hardwood floors.
2. Plug the cord set into a 120 volt outlet.
|
|
|
| Be sure that the plug fits tightly into outlet. |
| ||
|
|
|
|
| |||
|
|
| When plugs fit loosely into receptacles, they may slip |
| |||
|
|
| partially or completely out of the receptacle with only |
| |||
|
|
| the slight movement of the attached cord. Receptacles |
| |||
|
|
| in this condition may overheat and pose a serious fire |
| |||
|
|
| hazard; if covered by a curtain or drape, the fire hazard |
| |||
|
|
|
| ||||
|
|
| is even greater. |
|
| ||
3. | When the Fan is plugged in, there will be a “beep” to indicate there |
| |||||
| is power to the unit. |
|
| ||||
4. | Turn the Fan ON by pressing the Power Button ( | ). The Fan will |
| ||||
| “beep” twice to indicate that the unit has been turned ON. |
| |||||
5. | SPEEDS: Press the Fan Speed Button ( ) to desired speed |
| |||||
| setting. Each time the Fan Speed Button is pressed, the speed |
| |||||
| will change from Low (1), to Medium (2), to High (3). When intially |
| |||||
| plugged in, the Fan will be in Low Speed. When the Fan is turned |
| |||||
| OFF and ON again, the unit will resume the speed at which it was |
| |||||
| turned OFF. |
|
| ||||
6. | OSCILLATION: Press the Oscillation Button ( | ) to start and |
| ||||
| stop the oscillation function. |
|
| ||||
7. | TIMER: The timer function allows the unit to be set to operate for |
| |||||
| a length of time from 1/2 hour to 7 1/2 hours, in increments of 1/2 |
| |||||
| hour. Press the Timer Button ( ) to set the length of time desired. |
| |||||
| Each time the timer button is pressed, the time is increased by 1/2 |
| |||||
| hour. After reaching 7 1/2 hours, pressing the timer button once |
| |||||
| more will reset the Fan to continuous running. The lights on the |
| |||||
| front of the unit will light up appropriately with the length of time |
| |||||
| that the Fan is set for. |
| Figure 5 | ||||
8. | SLEEP: This function allows the unit to be set in Sleep Mode. | ||||||
| |||||||
Pressing the Sleep Button (
) once will set the unit on Low for 6 continuous hours. Pressing the Sleep Button (
) a second time will reset the unit to 6 continuous hours. The Oscillation Button (
) will function when the Fan is in Sleep Mode. Pressing any other button (Timer, Fan Speed or the Power Button) will shut off the Sleep Mode.
9.To turn the Fan OFF, press the Power Button (
) and unplug the unit from the electrical outlet.
Tamaño real de tornillos
4 por ventilador 4 por ventilador 2 por ventilador
ARMADO
| 1. Para facilitar el armado, recueste el Ventilador de modo que la | |
| parrilla negra y el tablero de control den hacia arriba. | |
| 2. Localice el Cable Eléctrico en la parte inferior del Ventilador. | |
| Coloque el Cable Eléctrico en los Canales Para Cable de los | |
| Soportes De Columna. Encaje firmemente los Soportes De | |
| Columna el uno con el otro de modo de formar un Conjunto De | |
| Soportes De Columna. (Figura 1) | |
| 3. Una el Conjunto De Soportes De Columna a la Base Del Motor | |
Remote Storage | con (4) Tornillos M5 de 1/2" de largo. Cerciórese de alinear la | |
| Llave del Conjunto De Soportes De Columna con la Muesca | |
| Localizadora de la Base Del Motor. (Figura 1) | |
| Conjunto De Soportes De Columna | |
|
| Base Del |
| Muesca | Motor |
|
| |
| Localizadora |
|
| Soportes De |
|
| Columna |
|
|
| Llave |
|
| Tornillos |
| Cable | M5 de 1/2" |
|
| |
| Eléctrico | Soportes De |
| Canales Para | Columna |
|
| |
| Cable | Figura 1 |
|
| |
4.Arme las Bases de Soporte, introduciendo las Copas en la Base de Soporte A en los Orificios De Copas de la Base de Soporte B. Pase el Cable de Electricidad por el orificio grande en el centro del Conjunto de la Base de Soporte. (Figura 2)
Conjunto de la Base de Soporte -
Vista des de Arriba
Cable
Eléctrico
Base de
Soporte A
5.Fije los Tornillos (2) #8 X 1/2" en los cuatro orificios que se encuentran en la parte inferior de la base. (Figura 3)
6.Alinee el Conjunto de la Base de Soporte con el Soporte de
Conjunto de la Base de Soporte -
Vista des de Abajo
Conjunto
de la Base de Soporte
| Cable |
| Eléctrico |
#8 X 1/2" |
|
Tornillos | Figura 3 |
|
Columna, cerciorándose de que el canal del cable en la parte inferior de la base de soporte esté orientado hacia la parte posterior del Ventilador. Ensamble el Conjunto de la Base de Soporte con el Conjunto del Soporte de Columna utilizando los Tornillos M5 de (4) 1" de largo. Jale con cuidado toda holgura excesiva del Cable de Electricidad e introdúzcala por el Canal Conductor de Cable. (Figura 4)
Conjunto de Columna Para la Base
Conjunto De
Soportes De
ConjuntoColumna de la Base
de Soporte
Canal
Conductor
de Cable M5 X 1"
Tornillos
Cable |
|
Eléctrico | Figura 4 |
|
Rev. F 9/07 | 4 |
| Base de | Copas |
|
| Soporte B |
|
|
|
| Figura 2 |
|
2530WGES | Rev. F 9/07 | 9 | 2530WGES |
