Lasko 4006 manual Save These Instructions, General Safety Information, Modelo

MODELO 4006

GENERAL SAFETY INFORMATION

When using electrical appliances, basic precautions should always be followed to re- duce the risk of fire, electrical shock and injury to persons, including the following:

Read all instructions before using this Fan.

1.Make certain the power source conforms to the electrical requirements of the Fan.

2.Make certain that the room is equipped with a working smoke detector.

3.Use this Fan only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electrical shock, or injury to persons.

4.To reduce the risk of personal injury and electric shock, the Fan should not be played with or placed where small children can reach it.

5.Unplug power cord before installing, servicing, or moving the Fan.

El Ventilador de Escritorio Ultra Delgado con Sujetador Clip Stik™ puede ser usado como Ventilador con Sujetador Clip Stik™ o como Ventilador de Escritorio.

Ventilador con Sujetador	Ventilador de Escritorio
Clip Stik™

	
	

	

FUNCIONAMIENTO

1.Coloque el Ventilador sobre una superficie firme y nivelada cuando use este producto como Ventilador de Escritorio. Vea las instrucciones debajo para adosar el Sujetador Clip Stik™ a una superficie.

ADVERTENCIA: Los tacos de plástico o hule, tales como las patas de esta unidad, pueden pegarse a la superficie de los muebles. La unidad podría dejar un residuo capaz de oscurecer, manchar o dejar marcas permanentes en el acabado de ciertas superficies de muebles, incluyendo superficies de madera y pisos de madera dura.

2. Conecte el cable eléctrico a un tomacorriente de 120 voltios.

DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN SERVICING OR MOVING THE FAN. ALWAYS UNPLUG THE POWER CORD. ALWAYS TURN OFF AND UNPLUG FAN BEFORE LEAVING THE AREA. NEVER LEAVE CHILDREN UNATTENDED WHEN THE FAN IS ON OR PLUGGED IN.

6.This Fan must NOT be used in potentially dangerous locations such as flammable, explosive, chemical-laden or wet atmospheres where gasoline, paint or flammable liquids are used or stored.

7.DO NOT use Fan in or near a window. Rain may create an electrical hazard.

8.Completely assemble Fan, according to instructions, before connecting to power supply.

This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. Match wide blade of plug to wide slot. Fully insert. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT attempt to defeat this safety feature.

This plug is a safety feature, to reduce the risk of fire, electric shock and personal injury. DO NOT remove, replace, repair or tamper with the originally supplied plug. If the Fan does not function properly, it may be due to the safety device incorporated in this plug. Return to an authorized service center or call 800-233-0268, Monday - Friday, between 8:00 a.m. and 5:00 p.m. EST. If the plug warning label is missing or damaged, call the toll free number for a replacement label.

9.Where possible, avoid the use of extension cords because the extension cord may overheat and cause a fire. If you must use an extension cord, minimize the risk of overheating by using the shortest cord possible and ensuring that it is UL listed. NEVER use a single extension cord to operate more than one Fan. DO NOT plug Fan into any other cord connected device, such as a power strip, cord reel, surge pro- tector, mutiple outlet adapters or outlet-type air fresheners. The use of such devices may create a fire hazard.

10.NEVER operate any Fan with a damaged cord or plug or after the Fan malfunctions, has been dropped or damaged in any manner. There are no user serviceable parts. Return Fan to an authorized service facility for examination, electrical or mechanical adjustment or repair.

11.NEVER insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock or fire, or damage the Fan. To reduce the risk of fire, DO NOT block or tamper with the Fan in any manner while it is in operation.

12.Always place the Fan on a stable, flat, level surface when operating, to avoid the chance of the Fan overturning. Locate the Power Cord so the Fan or other objects are not resting on it. DO NOT run Power Cord under carpeting. DO NOT cover Power Cord with throw rugs, runners or the like. Arrange Power Cord away from room traffic and where it will not be tripped over.

13.This Fan is not intended for use in wet or damp locations. Never locate a Fan where it may fall into a bathtub or other water container. NEVER use Fan where flammable liquids are used or stored.

14.NEVER use Fan outdoors.

15.This Fan is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please refer to Na- tional Electric Code (NEC) Article 547-7 (2002), or applicable state or local codes or standards relating to electrical requirements for Agricultural Buildings. THIS FAN DOES NOT MEET THE REQUIRMENTS OF NEC ARTICLE 547-7 (2002).

16.This Fan is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical requirements for Hazardous locations. THIS FAN DOES NOT MEET THE REQUIRMENTS OF NEC ARTICLE 500 (2002)

Ventilador de Escritorio: Para usar como Ventilador de Escritorio, no se necesita armado. Consulte la Sección de Funcionamiento. Ventilador con Sujetador Clip Stik™: Para armar correctamente el Ventilador con el Accesorio de Sujetador, siga las instrucciones debajo (Figuras 1 y 2) y proceda a la Sección de Funcionamiento.

ARMADO (Figuras 1 y 2)

1.Cuidadosamente retire el Ventilador y el Accesorio de Sujetador de la bolsa plástica y de la caja de cartón.

2.Deslice el extremo del Borde Plano del Accesorio de Sujetador al interior de la Ranura situada en la Parte Inferior del Ventilador. (Figura 1)

Accesorio de Sujetador	Figura 1
	Borde Plano

Sujetador

Ranura

Parte Inferior del Ventilador

Figura 2 Ventilador con Sujetador Clip Stik™ Armado

Asegúrese que el enchufe encaje firmemente en el

tomacorriente.

De no encajar firmemente en los tomacorrientes, podrían deslizarse parcial o completamente fuera del tomacorrientes apenas con un ligero movimiento del cable conectado. Los tomacorrientes en este estado podrían sobrecalentarse y presentar un grave riesgo de incendio; en caso de estar cubiertos por una cortina o paño, el riesgo de incendio es aún mayor.

3.Gire la perilla de control en el sentido de las agujas del reloj hasta fijar la posición de velocidad deseada:

0 - Apagado

2 - Alta Velocidad

1 - Baja Velocidad

4.Después de Apagar el Ventilador, desconecte la unidad del tomacorriente eléctrico.

Adosando el Sujetador Clip Stik™:

1.Adose el Sujetador Clip Stik™ a una estructura plana que tenga entre 1/4” y 1 3/4” de grosor o una barra de entre 1/2” y 1 3/4” de diámetro. Adosar el Sujetador Clip Stik™ a estructuras con anchos mayores o menores podría producir inestabilidad.

Pivote y Movimiento de Giro del Sujetador Clip Stik™:

(Figuras 3 y 4)

1.Para hacer pivotar el Sujetador Clip Stik™, sostenga el Accesorio de Sujetador y haga rotar el Ventilador hasta la posición deseada.

(Figura 3)

2.Para girar el Sujetador Clip Stik™, sostenga la Bisagra de Pivote sobre el Accesorio de Sujetador. Haga girar el Ventilador y/o el Accesorio de Sujetador de un lado a otro hasta alcanzar la posición deseada. (Figura 4)

Figura 3 Figura 4

Ventilador

 

		




REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK - DO NOT USE THIS FAN WITH ANY SOLID STATE SPEED CONTROL DEVICES.

SAVE THESE INSTRUCTIONS

Rev. C 9/07 2 4006ES

	Accesorio de	Bisagra de
	Sujetador	Pivote
Rev. C 9/07	7	4006ES