MODEL 4443
MODELO 4443
OPERATION (Figure 4)
This Fan may be operated by the local controls located on top of the unit (as shown in Figure 4 or by the Remote Control (shown in Figure 5).
1. Place the Fan on a firm and level surface.
CAUTION: Plastic or rubber tabs, like the feet on this unit, may stick to furniture surfaces and/or hardwood floors. The unit may leave a residue that could darken, stain or leave permanent blemishes on the finish of certain furniture surfaces, including wood surfaces, and/or hardwood floors.
2. Plug the cord set into a 120 V~ outlet.
|
|
|
| Be sure that the plug fits tightly into outlet. | Oscillation |
| |
|
|
|
|
| |||
|
|
|
| Button | Power | ||
|
|
| When plugs fit loosely into receptacles, they may | ||||
|
|
|
|
| Button | ||
|
|
|
|
| |||
|
|
| slip partially or completely out of the receptacle with |
|
| ||
|
|
|
|
|
| ||
|
|
| only the slight movement of the attached cord. Re- | Night Light |
|
| |
|
|
| ceptacles in this condition may overheat and pose a | Button |
| Fan Speed | |
|
|
| serious fire hazard; if covered by a curtain or drape, |
|
| ||
|
|
|
|
| |||
|
|
| the fire hazard is even greater. |
|
| Button |
3. Turn on the Fan by pressing the Power Button () on the unit or the remote control.
4. Speeds: Adjust the speed of the Fan by pressing the Fan Speed Button () after the power is turned on. Each time the speed button is pressed, the speed will change, from High (3), to Medium (2), to Low (1).
5.Oscillation: With the Fan on, press the Oscillation Button () to start and stop the oscillation function. The oscillation function can be used in any speed.
6. Nightlight: Press the Nightlight Button ( ) to turn on and off | Figure 4 | |
the light at the base of the Fan. The nightlight function will work | ||
| ||
when the Fan is ON or OFF. |
|
7.To turn the Fan OFF, press the Power Button () and unplug the unit from the electrical outlet.
HERRAMIENTAS NECESARIAS PARA EL
ARMADO (no incluida)
- Destornillador de Cabeza Phillips # 2
ARMADO
1.Para un armado más sencillo, deposite el Ventilador hacia abajo para que la parrilla frontal y el panel de control apunten hacia arriba.
2.Arme las Mitades de la Base de Apoyo encastrando las Puntas de la Base de Apoyo A con los Orificios para Puntas en la Base de Apoyo B. Conecte el Cable Eléctrico a través del orificio grande en el centro de la Montura de la Base de Apoyo. (Figura 1)
Puntas de la Base
de Apoyo A
| Puntas |
Puntas de la Base | Figura 1 |
de Apoyo B |
4.Alinee la Montura de la Base de Apoyo con la Base del Motor, teniendo en cuenta que la ranura del cable en la parte inferior de la montura de la base de apoyo debe apuntar hacia la parte posterior del Ventilador. Adose la Montura de la Base de Apoyo a la Base del Motor con (4) Tornillos Largos M5 de 1/2". Cerciórese de alinear la Llave del Conjunto de la Base de Soporte con la Muesca Localizadora de la Base Del Motor. (Figura 1) Suavemente tire del Cable Eléctrico para evitar que quede flojo y colóquelo en el Orificio de Colocación del Cable.
(Figura 3)
Montura de la
Base de Apoyo
3.Asegure (4) #8 X 1/2" Tornillos en los dos orificios externos en la parte inferior de la Base cuando mostrado. (Figura 2)
Puntas de la Base
de Apoyo B
| Orificio de |
| Colocación |
Tornillos | del Cable |
Cable Eléctrico | |
Largos M5 |
|
de 1/2" | Figura 3 |
Rev. A 10/10 | 4 | 4443ES |
Puntas de la Base |
|
|
de Apoyo A | Figura 2 |
|
|
| |
Rev. A 10/10 | 9 | 4443ES |