CONTROL REMOTO:
Todas las funciones realizadas con el Control Remoto operan del mismo modo que los controles manuales, excepto que usted no puede cambiar de °F a °C con el control remoto. (Figura 4)
1.Instale las dos baterías “AAA”.
2.No mezcle baterías viejas y nuevas. No mezcle baterías alcalinas, estándar (carbono-zinc) o recargables (níquel-cadmio).
3.NO SE DESHÁGA DE BATERÍAS EN EL FUEGO. BATERÍAS PUEDEN ESTALLAR O PUEDEN SALIRSE.
Vista Delantara | Vista Posterior |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
Figura 4
Si usted pierde su mando a distancia, por favor Cliente de llamada Serive para ordenar un reaplacement en 1-800 -233-0268, de lunes a viernes, entre las 8 a.m. y las 5 p.m. (Horario Estándar del Este de los Estados Unidos).
FUNCIÓN DE SEGURIDAD
1.Se incorpora un protector para sobrecargas térmicas a fin de impedir el sobrecalentamiento.
2.Si se alcanza una temperatura de sobrecalentamiento, el Calentador se apaga automáticamente. Sólo podrá reanudar su funcionamiento una vez que se reinicie la unidad.
Para Reiniciar el Calentador:
1.Desenchufe el Calentador y espere 10 minutos para que la unidad se enfríe.
2.Después de 10 minutos, enchufe el Calentador nuevamente y siga la INSTRUCCIÓN DE FUNCIONAMIENTO que se describe en este manual de instrucciones.
CONSEJOS PARA IDENTIFICAR PROBLEMAS
Si su Calentador se apaga inesperadamente o no funciona, es probable que la función de seguridad descrita anteriormente se haya activado para impedir el sobrecalentamiento.
1.Cerciórese de que el cable eléctrico esté enchufado en un tomacorriente en buen estado.
2.Revise su posición del Termostato. El Calentador podría estar apagado porque alcanzó la temperatura deseada.
3.El calentador portátil tiene un ventilador que seguirá funcionando aún cuando se apague el interruptor de encendido. Este ventilador va a seguir funcionando para enfriar el calentador portátil. Una vez que el ventilador deje de funcionar, usted puede desenchufar el calentador portátil.
4.Si su Calentador opera durante varios minutos y se apaga repetidamente, es posible que el mismo requiera limpieza. Ver la sección de Mantenimiento abajo.
Si tiene algún problema que no pueda resolverse con los pasos indicados más arriba, contacte a Asistencia Técnica al 1-800-233-0268, de lunes a viernes, entre las 8am y las 5pm (Horario Estándar del Este de los Estados Unidos).
OPERATION
1.Carefully remove the Heater from the plastic bag and the carton.
2.Place the Heater on a firm and level surface.
CAUTION: Plastic or rubber wheels may stick to furniture surfaces and/ or hardwood floors. The unit may leave a residue that could darken, stain or leave permanent blemishes on the finish of certain furniture surfaces, including wood surfaces, and/or hardwood floors.
3. Plug the cord set into a 120 volt outlet.
Be sure that the plug fits tightly into outlet.
When plugs fit loosely into receptacles, they may slip par- tially or completely out of the receptacle with only the slight movement of the attached cord. Receptacles in this condi- tion may overheat and pose a serious fire hazard; if covered by a curtain or drape, the fire hazard is even greater.
4.When the Heater is initially plugged in, there will be a ‘beep’ and the Power Light will come on indicating that there is power to the unit. The Power Light will remain lit until the Heater is unplugged from the electrical outlet.
5.Turn the Heater ON by pressing the Power Button (
). Note: The Heater “fan” has a 20-second delay before turning on. The purpose of the Delay Start Function is to allow the Infrared Quartz Element to heat up before the fan begins to circulate the airflow.
6.Upon turning the Heater on, the unit will be in HIGH heat (1500 Watts).
7.Press the (
) button for LOW heat.
8.To turn the Heater OFF, press the Power Button (
). Note: The Heater “fan” will run for 60 seconds before turning off completely. The Fan will continue to circulate the airflow after the power is turned off to circulate the warm air from the Infrared Heater cooling the unit down. Unplug the Heater from the electrical outlet.
Timer Function (Figure 1)
The timer function may be activated when the Heater display is in any func- tion or speed. This function allows you to set the length of time the Heater will run before turning itself off, from 1 hour to 8 hours. Pressing the Timer Button (
) will increase the length of time by 1 hour each time this button is pressed. After the display reflects 8 hours, pressing the Timer Button (
) once more will reset the Heater to run continuously. The Heater will turn off when the set time has elapsed. The unit can be turned back on by pressing the Power Button (
).
Save-Smart™
Press ( 
) to activate the Save-Smart™ Function.
1.Set the thermostat to desired temperature using the +/- buttons (Note: The default Save-Smart™ temperature is 72 º F)
2.When you reach the temperature at which you want to set the unit, the set temperature will flash several times and then the display will return to indicate the current room temperature and will gradually change as the room temperature changes.
3.When the air temperature is less than the set temperature, the heater will run in HIGH heat.
4.Once the thermostat reaches the set temperature the heater will automatically switch to LOW heat to save energy.
5.When the air temperature reaches 3º above the set temperature,
the heater will turn off. The Heater will cycle off and on in the LOW mode to maintain the set temperature.
All this happens automatically with Lasko Save-Smart™ Technology. To deactivate the Save-Smart™ function, press Save-Smart™ again or (
) for continuous high/low heat.
AUTOMATIC TEMPERATURE CONTROL (Figure 2)
The automatic temperature function will only operate on "High" heat . You cannot set the temperature automatically when the unit is in the low heat mode.
1. To set the room at a specific temperature press the (
) or ( ) buttons to the desired temperature.
2.When you reach the temperature at which you want to set the unit, the set temperature will flash several times and then the display will return to indicate the current room temperature and will gradually change as the room temperature changes. NOTE: the temperature display does not indicate the temperature of the heated air being emitted by the heater.
3.Once the room temperature reaches 2 degrees above the set tem- perature, the Heater will shut off. Once the room temperature reaches 1 degree below the set temperature, the Heater will turn back on and continue to cycle off and on to maintain the set temperature.
4.This function will cancel if the (
) button is pressed. The Heater will now be in High heat and run continuously.
NOTE: It is normal for the Heater “fan” to run for approximately 30 seconds when the Heater shuts off after reaching the set temperature. Press the (
) and ( ) buttons at the same time to change the display to ° Celsius. Press the same two buttons together again to change the display back to ° Fahrenheit.
