Lenmar Enterprises LAC50 important safety instructions Operating Instructions, Troubleshooting

POWERED BY

Model LAC50

Laptop Power Adapter

For Netbook Computers

Important Safety Instructions are included.

Please read the entire manual before use.

Owner’s Manual

Thank you for purchasing the LAC50 Laptop Power Adapter.The LAC50 provides regulated DC 9.5 to 20 volt output, which is adjustable by preset increments. The LAC50 will also accept input voltages ranging from 100 to 240VAC, allowing for worldwide use.The unit will support laptops requiring peak power up to 50W. The package includes the power unit, AC power cord and five adapter plugs to fit most popular laptop computers.

OPERATING INSTRUCTIONS

Do not use the adapter to power a device that exceeds 50 W maximum power rating. Make sure the adapter is disconnected from the AC outlet and the laptop before making any adjustments to the voltage settings. Make sure you have selected the proper voltage setting and the correct connector before connecting to your laptop.

ADJUSTING THE OUTPUT VOLTAGE

Follow these steps to adjust the output voltage on the LAC50.

3.) Review the power or ID plate on the laptops original
AC / DC power supply usually used to power the device.	DC	RATING:18V
Look for the word “DC RATING or OUTPUT” followed
by a number and VDC.
Example: OUTPUT = 18VDC or 18V DC

AC ADAPTER LABEL

NOTE: The specific notation “VDC” might not be indicated, Instead the following international symbol shown might be used 18 .

In some cases you may determine the desired voltage is between whole numbers such as 15.5VDC. In this case use the next higher voltage setting (16VDC)

Adjusting the Output Voltage		20V 19V 16V 12V 10.5V 9.5V
To adjust the output voltages just slide
the selector switch to the required voltage.
Polarity
			SWITCH
Look for this symbol in any of the three locations
mentioned above that looks like the following:
	CENTER POSITIVE

Use the diagram shown above to verify that you laptop uses “center positive” polarity as most all laptops use “center positive” polarity. Do not use the LAC50 if your laptop shows “center negative” polarity.

Adapter Tips

The LAC50 comes with 5 adapter tips. Select the

adapter tip that corresponds to your model by

Determine the required voltage setting and polarity of the power adapter by one of the following 3 methods.

1.) The voltage indication marked next to the input jack on the laptop device to be powered.

Example: VIN: = 18VDC or 18V DC

2.) Review the power ID plate on the bottom of the laptop to be powered. Look for the word “DC RATING or INPUT” followed by a number and VDC.

Example: DC RATING: 18VDC or INPUT: 18VDC

1.

VIN:	= 18VDC
	SIDE OF LAPTOP

RATING:18V

DC

BOTTOM OF LAPTOP

visiting www.lenmar.com/adaptertips Verify the fit
by plugging it into the power input on your laptop.	LAC50	TIP (5x)
It is important that the center contact or pin be the
correct size to insure proper electrical contact.

Do not force the tip in, it should slide in as easily as your original did. If it does not fit easily please verify you have the correct tip listed in our reference. Connect the selected adapter tip to the end of the LAC50.

Plug the LAC50 into the laptop, then plug the AC power cord into the AC jack on the adapter and then into a standard AC outlet.The Blue LED power indicator will light showing the LAC50 is functioning correctly.

2.

TROUBLESHOOTING

Some laptop computers have power supplies in excess of this power adapter (50 Watts).In most cases, the higher rating is used to both charge a completely discharged battery and power the laptop at the same time. This power adapter can be used for such applications, but it is recommended that the computers battery be fully recharged before using the adapter to operate the laptop.

NOTE: This power adapter can power,but may not be able to charge battery for some Dell® models.

If the indicator turns off while the power adapter is in use, this indicates that the power requirement of the device is beyond the maximum output of the LAC50 and that overload/short circuit protection has been activated.

NOTE: It is normal for the LAC50 to be warm during use.

Notice

•Keep the LAC50 dry, if it gets wet wipe it dry immediately.

•Use and store it in normal temperature environments.

•Handle the LAC50 carefully, do not drop it.

•Do not use the LAC50 if the cords become damaged.

Keep the LAC50 away from dust and dirt; wipe it with a cloth occasionally to keep it clean.

There are no user serviceable parts inside! Modifying or tampering with its internal components can cause a malfunction and will invalidate its warranty. If your LAC50 is not performing as it should during the warranty period, contact Lenmar for warranty service.

SPECIFICATION

Input: AC 100-240V-50/60Hz

Adjustable Output: DC 9.5(9)/10.5(10)/12/16/19/20V, 3A -2A max

Polarity: Center positive

Continuous Output Power: up to 40 W

Peak Output Power: 50W

Meets CEC Standard: Minimum Efficiency>83% at DC20V

Adapter Power Tips: 5 plugs supplied.

Unit Dimensions and Weight: 117g

AC Extension Cord Length: 1.20 meters (47”)

DC Extension Cord Length: 1.50 meters (59”)

Dimensions: 93 x 50.5 x 29mm

WARRANTY

This limited warranty starts from the date of original purchase and expires 2 years thereafter. If, during this period, any part, because of manufacturing defects or workmanship fails to function properly under normal use will be repaired at no charge for parts and labor or, at our option, the product will be replaced. The following is excluded: damages from delay or loss of use of equipment, or damaged batteries, malfunctions resulting from misuse, tampering, unauthorized repairs, modifications, or accident. Package the unit and its accessories carefully using ample padding material to prevent damage in transit and ship it prepaid and insured to:

LENMAR ENTERPRISES, INC.

4035 VIA PESCADOR

CAMARILLO, CA 93012 USA

When sending in product for service, your package should include evidence of date and place of purchase. Enclose $10.00 for shipping and handling for addresses in the U.S. and $15.00 in Canada. For outside the U.S. and Canada, freight will vary depending upon ship-to address.

Proposition 65 Notice (California)

The following statement is required in the state of California pursuant to the settlement of an action brought by the Mateel Environmental Justice Foundation against multiple electronics and appliance manufacturers

• WARNING: Handling the cord on this product will expose you to lead, a chemical known to

the state of California to cause birth defects or other reproductive harm.

Wash hands after handling.

For further information contact

Lenmar Enterprises, Inc.

Product Service Department

Phone: (800) 424-2703

E-mail: sales@lenmar.com

Visit Our Web Site at: www.lenmar.com

310-076-34-0402 r1

3. 4.