Standard Installation ConÞgurations Into an Existing Fireplace

Model: ProÞle¨ 30 INS-2

IMPORTANT

Make sure the chimney and Þrebox are clean and free of soot and ashes before installation begins. Failure to do so may result in the transfer of soot into the room by way of the room air blower.

Model: ProÞle 30 INS-2

 

 

Listed Pellet

Model: ProÞle 30 INS-2

IN CANADA Ð Installing as a Horizontal

 

 

 

 

 

 

 

 

Vent Cap

 

 

 

 

 

Vent is not allowed. The Þreplace

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

chimney must be fully lined.

 

 

 

 

 

 

 

 

 

Horizontal Vent

 

 

 

 

 

 

 

 

 

 

(Direct Vent)

 

Full Chimney

 

 

 

 

 

 

 

 

 

Reline (required when

 

 

 

 

 

 

 

 

 

installing into a Factory

 

 

 

U.S.A. Ð The insert may be

 

Built Fireplace)

 

 

 

installed as a Direct Vent (hori-

 

 

 

 

 

 

 

 

 

 

zontal vent through the chimney

 

 

 

 

 

 

 

 

 

 

structure) in masonry Þreplaces

 

 

 

 

 

 

 

 

 

 

if local codes will permit.

 

Approved Liner for Factory Built

 

 

 

 

 

 

 

 

 

(ZC) Fireplaces and Masonry

 

 

 

 

 

 

 

 

 

Fireplaces is 2100HT (degree

 

 

 

Canada Ð Installing an insert a s

 

F.) liner listed to UL 1777 or

 

 

 

a Direct-Vent is not allowed. The

 

ULC S635. The liner must be

 

 

 

Þreplace chimney must be fully

 

securely attached to the insert

 

 

 

relined from the insert outlet to

 

ßue collar and the chimney top.

 

 

 

termination.

 

 

 

 

 

 

 

 

 

Positive Flue

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Connection

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Recommended

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

18Ó Min.

 

 

 

 

 

18Ó Min.

 

 

 

 

(457 mm)

 

 

 

 

 

(457 mm)

 

 

 

 

 

 

 

 

 

 

 

to Mantel

 

 

 

 

 

to Mantel

 

 

 

 

 

 

 

 

 

 

Clean-Out

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Tee

 

 

 

 

 

 

 

 

 

 

 

 

1Ó Min.

 

 

 

 

 

1Ó Min.

 

 

 

 

 

 

(25 mm)

 

 

 

 

 

6Ó

 

 

 

6Ó

 

 

 

(25 mm)

 

 

 

to Trim

 

 

 

 

Min.

 

 

 

Min.

to Trim

 

Figure 30 - Full Chimney Reline

 

Figure 31 - Horizontal Direct Vent

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Listed Pellet Vent

 

 

 

 

 

 

 

 

 

 

Termination Cap

 

 

IMPORTANT NOTES:

 

1 foot Section of PL

 

 

 

Chase Cover

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A ßexible corrugated chimney liner has much greater resistance to

 

 

 

 

 

 

 

 

Vent (listed to UL 641

 

 

 

 

 

 

 

 

 

 

 

 

 

the ßow of ßue gases than does a rigid liner. For this reason we

 

or ULC S609)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

recommend that a larger, 4Ó liner be used on vertical runs exceeding

 

 

 

 

 

 

 

 

 

 

 

 

 

Termination When

 

 

15 feet or that rigid venting be used as illustrated on this page (see

 

 

 

 

 

Connected to

 

 

Full Chimney Reline).

 

 

 

 

 

Masonry Chimney

 

 

If a ßexible corrugated chimney liner is used, it must be fully extended

 

 

 

 

 

or Existing Class

 

 

 

3Ó or 4Ó liner

 

 

A Chimney

 

 

to eliminate any sagging and to improve the exhaust ßow.

 

 

 

 

 

 

 

(listed to UL 1777

 

 

Do not block opening at front of insert (below door).

 

or ULC S635)

 

 

 

 

Figure 32 - Existing Chimney Termaination

 

 

 

18

 

 

 

 

 

 

 

 

 

 

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE