Accessing Ash Clean-Out Ports Ð Model: ProÞle 30 FS-2 and ProÞle

 

 

(Recommended

 

 

30 INS-2

 

 

Frequency of 1 year)

 

 

 

 

 

 

 

 

 

 

1) Open firebox door.

 

 

 

 

 

2) Using a 5/16” nut driver, loosen the screws on the two clean-out covers

 

 

 

 

 

(until screw heads will release through the key hole slots). Remove

 

 

 

 

 

covers.

 

 

 

 

 

3) Using an approved ash vacuum (a brush can also be used), remove

 

 

 

 

 

the ash build-up.

 

 

 

 

 

4) After cleaning, reinstall the clean-out covers and tighten screws.

 

 

 

 

 

5) Close firebox door.

 

Figure 41 - Sweep Away Debris from Behind Window Wash Bracket

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Ash Clean-out Ports

 

 

 

 

 

 

 

 

 

 

 

 

IMPORTANT

 

 

 

 

 

 

 

 

 

 

 

¥ Ensure appliance is cold before beginning.

 

 

 

 

 

¥ Firebrick panels must be installed before operat-

 

 

 

 

 

ing unit.

 

(Minimum Frequency

Remove Covers And

 

 

¥ Model proÞle¨ 30-2 series has a cover installed

 

Vacuum Out Fly Ash

 

 

 

of 1-2 months)

 

 

 

 

 

over each clean-out port. The covers must be

 

 

 

 

 

reinstalled before operating the unit.

 

Figure 43 - Accessing Ash Clean-Out Ports – Profile 30 Series

 

¥ Ash clean-out ports must be cleaned out as part

 

 

 

 

 

 

 

of routine maintenance.

 

UltraGrate™ (Burn Grate for All Models)

 

Accessing Ash Clean-Out Ports Ð Model: ProÞle 20 FS-2

 

 

 

 

 

1) Open firebox door.

Inspect the UltraGrate periodically so that the air holes don't clog with ash

 

or clinkers. The UltraGrate can easily be cleaned with the grate scraper

 

2) Remove Firebrick Panels:

 

/ ash pan tool, or it can be removed for cleaning. It is very important to

 

a. Remove the two firebrick retainer brackets using a 5/16” nut

 

monitor the ash build up under the UltraGrate, as too much of ash will

 

driver (located on the left and right side of the firebrick inside

 

block combustion air from entering the grate, causing pellets to pile-up

 

firebox). Loosen the screws (do not remove) until screw heads

 

can be removed through the key hole slots in the brackets.

in the grate. The ash build-up under the grate is easily dumped into the

 

b. With the brick retainer brackets removed, lift firebrick panels up

ash pan by pulling out the ash slide weekly (see Ash Slide Plate, Figure

 

and out.

45). The grate cleaning procedure is the same for all models.

 

3) Using an approved ash vacuum (a brush can also be used), remove

 

 

 

 

the ash build-up.

 

 

 

 

4) Reinstall firebrick panels.

 

 

 

 

5) Close firebox door.

UltraGrate

 

 

 

 

 

(Recommended Fre-

 

Vacuum Out Fly Ash

 

quency of 1-2 months)

 

Clean-Out Ports (indi-

 

 

 

cated by arrows)

(Recommended Frequency

 

 

(firebox viewed from front with

firebrick panels removed)

 

of 1 day Ð 2 weeks)

 

 

 

 

 

Figure 44 - Inspect UltraGrate and Clean if Necessary

Figure 42 - Ash Clean-Out Ports, Profile 20 FS-2

24

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE