Lennox Hearth ADK40CPB, ADK45CBS installation instructions Tables, Arch Door Kit with Brass Trim

	LENNOX HEARTH PRODUCTS
	KITS AND ACCESSORIES
P/N 750,021M	ARCH DOOR KITS WITH BRASS OR
REV. E 03/2008	BRUSHED STAINLESS STEEL TRIM

INSTALLATION INSTRUCTIONS FOR ARCH DOOR KITS WITH BRASS OR BRUSHED STAINLESS STEEL TRIM

FOR USE WITH MERIT™, MERIT PLUS™, OR ElITE® Series gas fireplaces

KIT CONTENTS:	TOOLS REQUIRED:
1 ea. Arched Door	None
1 ea. Instruction Sheet

GENERAL INFORMATION

These arch door kits may be used with gas fireplace models listed in

Tables 1 & 2.

CAUTION

INSTALL ONLY WHEN THE FIREPLACE IS OFF AND COLD!

INSTALLATION INSTRUCTIONS

Part A: Elite Series Fireplaces

Step 1.Slightly lift and pull the existing top radiant panel/hood assembly away from the fireplace, or pull hood and slightly lift and pull the existing louver assembly away from the fireplace.

Step 2. Lift and pull the existing top and bottom bustle away from the fireplace.

Step 3.Open the bottom compartment door (either a radiant panel or louver assembly) by pushing in simultaneously the left and right top corners of the door (the door is hinged at the bottom).

Step 4.Remove the bottom compartment door by sliding the hinge pin, located at the door’s left side, to the right until it disengages from the left corner post hole. Pull the door diagonally to the left, away from the fireplace.

Step 5.Remove the modesty panel as follows: lift the modesty panel by the tab on the panel’s right end, pull the right end of the panel away from cabinet and then pull the panel diagonally out of the corner post slots on the left side of the unit. Remove the modesty panel carefully, so that none of the wires become loose or disconnected.

Arched Door

Glass

Frame

Figure 1	Corner Tabs- At
	The Four Corners

Step 6.Open the glass door latche(s) located underneath the firebox.

Step 7.Remove the door from the fireplace by swinging the bottom of the door outward and lifting it up and away.

Step 8.Center the arch door over the glass frame as shown in Figure 1. Press the arch door onto the glass frame and bend the four corner tabs into the frame’s U-channel as shown in Figure 2.

CAT. NO.	MODEL	WHERE USED
81L34	ADK35CPB	EDV3530, ED3530
81L35	ADK40CPB	EDV4035, ED4035-2, LMDV-4035,
		SSDV-4035, MPD4035, EDVST, EDST-2,
		EDVPF, EDPF-2, EDVCR, EDCR-2, EDVCL,
		EDCL-2, EBST-2, EBVPF, EBPF-2, EBVCR,
		EBCR-2, EBVCL, EBCL-2
81L36	ADK45CPB	EDV4540, ED4540-2, MPD4540
81L37	ADK24CPB	EDVPF, EDPF-2, EDVCR, EDCR-2, EDVCL,
		EDCL-2, EBVPF, EBPF-2, EBVCR, EBCR-2,
		EBVCL, EBCL-2
98L05	ADK33CPB	MDR3328, MDT3328, MPDT3328,
		MPDR3328, LMDVR-3328
26M43	ADK35CMPB	MPD3530, MPD35ST, MPD35PF, MPB35ST,
		LMDV-3530, ssDV-3530
H7026	ADK22CMPB	MPD35PF
Table 1 - Arch Door Kit with Brass Trim

CAT. NO.	MODEL	WHERE USED
98L68	ADK35CBS	EDV3530, ED3530
98L69	ADK40CBS	EDV4035, ED4035-2, LMDV-4035,
		SSDV-4035, MPD4035, EDVST, EDST-2,
		EDVPF, EDPF-2, EDVCR, EDCR-2, EDVCL,
		EDCL-2, EBST-2, EBVPF, EBPF-2, EBVCR,
		EBCR-2, EBVCL, EBCL-2
98L70	ADK45CBS	EDV4540, ED4540-2, MPD4540
98L71	ADK24CBS	EDVPF, EDPF-2, EDVCR, EDCR-2, EDVCL,
		EDCL-2, EBVPF, EBPF-2, EBVCR, EBCR-2,
		EBVCL, EBCL-2
98L62	ADK33CBS	MDR3328, MDT3328, MPDT3328,
		MPDR3328, LMDVT-3328, LMDVR-3328
26M44	ADK35CMBS	MPD3530, MPD35ST, MPD35PF, MPB35ST,
		LMDV-3530, ssDV-3530
H7027	ADK22CMBS	MPD35PF

Table 2 - Arch Door Kit with Brushed Stainless Steel Trim

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.