| LENNOX HEARTH PRODUCTS |
| KITS AND ACCESSORIES |
|
|
P/N 504,223M | CLEAN FACE PANEL KITS |
REV. F 03/2008 | (PAINTED FINISH) |
INSTALLATION INSTRUCTIONS FOR CLEAN FACE PANEL KITS FOR USE WITH
MERIT ™, MERIT PLUS ™ OR ELITE® SERIES GAS FIREPLACES
KIT CONTENTS: | TOOLS REQUIRED: | |
|
| |
1 ea. Top Radiant Panel |
| |
1 ea. Bottom Radiant Panel | None | |
1 ea. Lennox Nameplate | ||
| ||
1 ea. Instruction Sheet |
| |
|
|
CAT. NO. | MODEL | WHERE USED | |
88L36 | EDV3530, ED3530 | ||
MPD35ST/PF, MPB35ST | |||
|
| ||
|
|
| |
|
| EDV4035, | |
|
| EDVST, | |
88L37 |
Top Radiant Panel
Bottom Radiant Panel
GENERAL INFORMATION
CAUTION
INSTALL ONLY WHEN THE
FIREPLACE IS OFF AND COLD!
|
| ||
|
| ||
|
|
| |
88L38 | EDV4540, | ||
|
|
| |
88L35 | EDVPF, | ||
|
| EBVCL, | |
|
|
| |
98L12 | RAD33C | MDR3328, MDT3328, MPDT3328, | |
MPDR3328 | |||
|
|
These clean face panel kits may be used with Merit™, Merit Plus™ or Elite® series gas fireplaces listed in Table 1.
INSTALLATION INSTRUCTIONS
Note: Do not operate fireplace without the eyebrow installed in its normal position. See Figure 1 for models with louvers or Figure 2 for models with clean face panel.
Step 1.Grasp the existing eyebrow and pull it forward away from the fireplace (it is held in place by spring tension). See Figure 1.
Step 2.Slightly lift and pull the existing top louver assembly away from the fireplace.
Step 3.Slide the existing eyebrow into the slots on the lower edge of the top radiant replacement panel.
Step 4.Hang the top radiant panel/eyebrow assembly in the opening previously occupied by the top louver assembly. See Figure 2.
Step 5.Open the bottom louver assembly by pushing in simultaneously the left and right sides of the louver assembly (the assembly is hinged at the bottom).
Step 6.Merit Series Units - Remove the assembly from the fireplace by
removing the hinge screw and spacer on each end of it.
Merit Plus and Elite Series Units - Remove the assembly from the fireplace by sliding the hinge pin, located at the door’s left side, to the right until it disengages from the left corner post hole. Pull the door diagonally to the left, away from the fireplace.
Step 7. Snap the replacement Lennox nameplate logo into the 2 holes provided in the replacement panel.
Step 8. Merit Series Units - Install the replacement bottom radiant panel using the existing hinge screws and spacers.
Merit Plus and Elite Series Units - Install the replacement bottom radiant panel by inserting the right side locating pin into the right cabinet corner post and then the left side
26M47 | RAD33MC | MPD3530, MPD35ST |
|
|
|
H7019 | MPD35PF |
Top of Appliance
Louver Assembly
Top of Door Frame
Hood must be installed as shown.
Figure 1 - Louvered FaceTop of Appliance
Top Radiant Panel
Top of Door Frame
Hood must be installed as shown.
Figure 2 - Clean FaceNOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and the discontinuance of colors, styles and products. Consult your local distributor for fireplace code information.
Printed in U.S.A. © 2001 by Lennox Hearth Products | Lennox Hearth Products |
P/N 504,223M REV. F 03/2008 | 1110 West Taft Avenue • Orange, CA 92865 |