Wallplate Mounting:
1/64" (0.4 mm)

Acentiª Wallplate Kit

INSTALLATION INSTRUCTIONS

WARNING: To be installed and/or used in accordance with appropriate electrical codes and regulations.

WARNING: If you are unsure about any part of these instructions, consult a qualified electrician.

NOTE: Refer to the individual Acentiª device's instruction sheet for complete wiring details.

NOTE: For the purposes of illustration, this instruction sheet will show the mounting of the Acenti Wallplate System using the Acenti Switch. The mounting of the Acenti Wallplate System will be the same for all Acenti devices.

NOTE: For wallplate installation only, go To Step 5.

INSTALLING ACENTIª WALLPLATE KIT WARNING: TO AVOID FIRE, SHOCK, OR DEATH; TURN

OFF POWER at circuit breaker or fuse and test that power is off!

Step 1 Check Device And Alignment Plate:

¥The installation of your Acenti device should now be at the point where all your electrical connections are complete and secure.

¥If the Alignment Plate was temporarily positioned during the installation of Acenti device, go to Step 2.

¥If the Alignment Plate was not used during the installation of Acenti device, go to Step 3.

Step 3 If Alignment Plate Was Not Pre-Installed:

¥In order to relieve stress on device when mounting, dress wall box wires with a bend (refer to Figure).

¥Carefully pass the wired Acenti device through the Alignment Plate ensuring the tab is towards the bottom.

¥Go to Step 4.

Mounting Screw

Cut-Out (2 places)

Alignment Plate

Tab

Step 4 Device Mounting And Alignment:

CAUTION: DO NOT over-tighten device mounting screws. Over-tightening will cause improper mounting and alignment. Using a high-torque power screwdriver is not recommended.

Alignment Plate must sit completely flush on wall surface.

For Multi-Gang Installations

For multi-gang installations, the alignment of the devices installed is important. If necessary, adjust the space between the paddles/faces to maintain a consistent gap of approximately 1/64" (0.4 mm). This can be done by gently tapping the strap of the devices in the direction needed with a small screwdriver as shown.

Step 2 If Alignment Plate Was Pre-Installed:

¥In order to relieve stress on device when mounting, dress wall box wires with a bend (refer to Figure).

¥Remove mounting screw or electrical tape that is temporarily holding the Alignment Plate.

¥Go to Step 4.

TOP

TOP

¥Ensure that cut-outs in alignment plate are positioned such that the device mounting holes in the wall box are accessible and tab is on bottom.

¥Begin to partially screw in device mounting screws into wall box mounting holes.

¥Align the three tabs in the multi-function clips with the alignment pins on the Alignment Plate and press into place.

¥Continue mounting of device and Alignment Plate by tightening the mounting screws until the strap sits flush and just snug on Alignment Plate.

¥Reposition Alignment Plate for leveling if necessary. Complete installation by lightly tightening mounting screws until Alignment Plate sits flat on wall surface.

Step 5

Mounting: With "LEVITON" facing up and notch facing down, press Acentiª wallplate onto device until it clicks flush to wall surface.

Removal (if necessary):

Place a small screwdriver in notch on bottom of wallplate and gently lift up to remove.

TOP

TOP

Wall Surface

Pin and alignment hole

engaged (2 Places)

Wallplate

Notch on bottom

RESTORING POWER:

TOP

TOP

TOP

TOP

TOP

TOP

 

Alignment pin into

Strap must sit flat on

alignment hole

alignment plate.

with 3 tabs.

 

 

Restore power at circuit breaker or fuse. Installation is complete.

For additional information, contact the

Acentiª Information Hotline at 1-888-4-ACENTI

or visit Leviton's website at www.leviton.com/acenti

U.S. & Foreign Patents Pending

Copyright© 2004 Leviton Manufacturing Co., Inc.

All Rights Including Trade Dress Rights Reserved

PK-93603-10-03-0B

Page 1
Image 1
Leviton ACENTI installation instructions Installation Instructions, Restoring Power, Top

ACENTI specifications

Leviton ACENTI is an innovative line of electrical solutions designed to enhance both residential and commercial spaces. This product line embodies advanced technology and functionality, ensuring customers benefit from modern electrical management systems. The ACENTI series primarily focuses on providing user-friendly, efficient, and reliable electrical solutions that simplify control over various devices and systems.

One of the standout features of Leviton ACENTI is its seamless integration with smart home technology. The series supports various communication protocols, including Wi-Fi, Zigbee, and Z-Wave, allowing users to connect and control their electrical systems from anywhere using a smartphone or tablet. This remote access ensures convenience and enhances energy management by allowing users to monitor usage patterns and optimize energy consumption.

ACENTI offers a wide range of devices, including smart switches, dimmers, and outlets, with user-centric design elements. For instance, the dimmers feature intuitive touch controls and customizable lighting scenes, which can significantly enhance the ambiance of any room. The smart outlets, equipped with built-in energy monitoring, allow users to track their energy usage in real-time, promoting energy efficiency.

Security is a high priority with the ACENTI line, as it includes features that enhance home security. Users can set schedules for lights to turn on and off, giving the appearance of occupancy when away. Additionally, the devices offer an added layer of protection with built-in surge protection, ensuring longevity and reliability in today's electrical landscape.

Installation of the ACENTI products is straightforward, with many devices designed for easy retrofitting into existing electrical systems. This ease of installation is complemented by Leviton's robust support resources, including user-friendly manuals and online guides, making it accessible for both professionals and DIY enthusiasts.

Moreover, the aesthetics of ACENTI devices make them a perfect fit for any decor. With a variety of finishes and styles available, users can customize their space without compromising on design.

In summary, Leviton ACENTI combines technological advancements with practical design, providing consumers with a range of smart electrical solutions that enhance convenience, security, and energy efficiency. Its commitment to quality and innovation positions it as a leading choice for modern electrical management in diverse environments.