LG Electronics manual 16

EZ-Manager Wizard (Cont.)

Manual Pro:Centric Configuration

1. With the Searching for Pro:Centric Server screen on display,

EZ-Manager Wizard

use the arrow keys on the Installer Remote to select/highlight

1

2

3

4

the Manual Pro:Centric option at the bottom right of the

Pro:Centric Manual Configuration

Pro:Centric Mode

<

GEM

>

screen, and press OK.

Data Channel

1

In the Pro:Centric Manual Configuration screen (see example

Signal Strength

0%

No signal

at right), you will be able to configure the appropriate

Signal Quality

0%

Pro:Centric settings in the TV. Use the Up/Down arrow keys

on the Installer Remote to navigate between fields.

Back

Exit

Next

2. In the Pro:Centric Mode field, use the Left/Right arrow keys

EZ-Manager Wizard

to select the appropriate Pro:Centric Application Mode—

1

2

3

4

GEM, FLASH, or Configuration Only.

Pro:Centric Manual Configuration

Note: For remote management only, select “Configuration

! Are you sure you want to exit the wizard?

>

Pro:Centric ModeIf you select ‘OK’<now, your settingsGEMwill be lost

Only.” The TV will search for TV E-Z Installation data down-

and you will exit

the setup wizard.

Channel Number

1

loads; however, Pro:Centric application data will not be

Signal Strength

0%

This window will close and you will be returned to

the previous page automatically in 2 seconds.

0%

downloaded, i.e., Installer Menu item 098 PRO:CENTRIC will

Signal Quality

OK

Cancel

Save and Exit

No

be set to 0.

3. In the Data Channel field, either key in or use the Left/Right

Back

Exit

Next

arrow keys to select the RF channel number that will be

EZ-Manager Wizard

used by the Pro:Centric server as its data channel. The Data

1

2

3

4

Channel value can be set from 1 to 135. *

Processing the Pro:Centric Configuration...

4. Once all fields are completed as required, you have two

Downloading the Pro:Centric application files takes a few minutes.

Please wait...

1%

options (see also note below):

Retrieving files from data channel 75

•

To save the data entered and exit the wizard, use the arrow

Maintenance files

Pending...

Application files

In progress...

keys to select Exit and then press OK. In the subsequent

pop-up confirmation window, select Save and Exit, and then

Warning - Do not remove AC power or the signal cables during these steps

press OK once more. The Pro:Centric application and/or E-Z

Installation data will be downloaded to the TV at a later time.

EZ-Manager Wizard

This option is useful, in particular, if the Pro:Centric server

1

2

3

4

has not yet been configured.

EZ-Manager Configuration Complete

•

To initiate a real-time download of Pro:Centric application

The TV will turn off in 3 second(s).

Installed Components

and/or E-Z Installation data, use the arrow keys to select

Pro:Centric Application

GEM application downloaded

Next, and then press OK.

Maintenance Files

LP645H_Config.tlx

The EZ-Manager Wizard will proceed with the remaining

Pro:Centric application and/or E-Z Installation data down-

Reboot

Turn Off

load steps, as shown on the Processing the Pro:Centric

Configuration screen.

Note: Pro:Centric server data must be present on the RF channel selected as the TV’s Data Channel in order for you to select “Next” (you will see a “Data Channel found” message below the signal strength indicator).

When the Pro:Centric configuration is complete, an EZ-Manager Configuration Complete screen is displayed, and after 10 seconds, the wizard exits, and the TV turns OFF.

Note: With the EZ-Manager Configuration Complete screen on display, you also have the option to manually turn off or reboot the TV. If desired, select Turn Off or Reboot, respectively, and then press OK on the Installer Remote.

*PCS150R and later Pro:Centric servers do not support HRC or IRC cable channel frequencies.

16 206-4232