Installer Menu (Cont.)
096 - DEF. ASP. RATIO (Default Aspect Ratio) Selects default aspect ratio at power up:
0 | = Set By System | 1 | = 4:3 |
2 | = 16:9 (default) | 3 | = Just Scan |
4 | = Zoom |
|
|
Note: This item is not available in the Installer Menu unless item 106 ASP RATIO LOCK is set to 0.
097 - AUDIO OUTPUT
Determines availability and signal type/level (fixed speaker, variable speaker, or fixed line level [amplifier]) of the audio output to be used by external audio equipment connected to the Speaker Out jack on the TV. Set to 0 to disable audio output. Otherwise, see the table below and set as required in accordance with audio equipment.
| Value | Status |
|
Speaker Output | 1 | Fixed 0.01 Watts | |
| 2 | Fixed 0.03 Watts | |
|
|
| |
| 3 | Fixed 0.05 Watts | |
|
|
| |
| 4 | Fixed 0.10 Watts | |
| 5 | Fixed 0.20 | Watts |
|
|
|
|
| 6 | Fixed 0.50 | Watts |
| 7 | Fixed 1.00 | Watt (default) |
|
|
| |
| 8 | Control with volume | |
Line Output | 9 | Fixed line level (typically 400 mVrms ± | |
|
| 100 mVrms @10KΩ) output | |
See also Reference section, “External Stereo Speaker Setup.”
098 - PRO:CENTRIC
Selects the Pro:Centric Application Mode. Set to 0 (default) to disable the Pro:Centric application. Set to 1 for Flash Mode. Set to 2 for GEM (Java Application) Mode.
In order to retrieve the Pro:Centric application, when enabled (for Flash or GEM Mode), the TV must be turned OFF/ON two times. Once you exit the Installer Menu, turn OFF the TV for at least one minute. When you turn the TV back ON, the TV will start the appropriate library based on the setting of this item. Wait until TV programming appears on the display, and then turn the TV back OFF, this time for a few minutes, to initiate the application down- load. When you turn the TV back ON, press the PORTAL key on the Installer Remote, and verify that the Pro:Centric application appears on the display.
Note: This item is not available in the Installer Menu when item 119 DATA CHANNEL is set to 0.
099 - BACK LIGHTING
Sets the TV screen brightness at power up. Default setting is 255.
•1 (dimmest
•101 (dimmest
•201 Automatic Static Back Lighting: Applicable for 32/42LY560M only. The TV automatically controls back lighting by using Intelligent Sensor to detect the level of ambient lighting.
•202 Automatic Dynamic Back Lighting: Applicable for 32/42LY560M only. The TV automatically controls back lighting by using Intelligent Sensor to detect the level of ambient lighting and depending upon the picture level of the current program.
If set to 201 or 202 (32/42LY560M only), back lighting can be controlled via the Picture settings in the TV setup menus. However, each time the TV is turned ON, Picture Mode (set in Picture Menu) is defaulted to Intelligent Sensor. If Picture Mode is manually set to a static option (Vivid, Standard, etc.) during a viewing session, Intelligent Sensor is temporarily disabled.
If set to 255, back lighting is controlled via the Picture settings in the TV setup menus.
102 - ATSC BAND
Sets up TV to receive different types of incoming signals:
0 = Broadcast, 1 = CATV, 2 = HRC, 3 = IRC, 4 = Same as NTSC.
103 - ATSC TUNE MODE
Sets ATSC tuning mode: Default set to 1 for Physical Channel scan. Set to 0 for Virtual Channel scan.
104 - START MINOR CHANNEL
Sets Minor Start Channel number at power up. 0 = NTSC. If not 0, number selected is the digital channel’s Minor Start Channel number.
Note: This item is not available in the Installer Menu when item 004 STRT CHANNEL is set to 0 or 255.
106 - ASP RATIO LOCK (Aspect Ratio Lock)
Set to 1 to retain previous aspect ratio with power off. Set to 0 to retain default aspect ratio with power off. See item 096 DEF. ASP. RATIO above.
116 - VIDEO MUTE EN (Video Mute Enable)
Applicable for analog channels only. If set to 1, video mutes (blank screen) when no signal is present.
29 |