Mechanical Installation

Mounting Methods

General Information

•Select the appropriate orientation to maximize sunlight exposure.

•Module should not be mounted or stored in a way that the front/top glass faces downward in order to prevent water from entering the junction box, which could cause a safety hazard.

•Clearance between the solar module frames and structures such as roofs or ground is required to prevent wiring damage and to allow air to circulate behind the solar module. The recommended standoff height is a minimum of 100mm

•When installed on a roof, the solar module must be mounted over a fire-resistant roof covering rated for the application. The fire resistance of the solar module is class C after ANSI/UL790.

•The solar module is only IEC listed for use when its factory frame is fully intact.

•Removal or alteration must be done by an authorized and qualified individual

•Creating additional mounting holes may damage the solar module and reduce the strength of the frame.

•We recommend a 6mm gap between module frames to avoid tension from thermal expansion.

•The fire rating of this module is valid only when mounted in the manner specified in the mechanical mounting instructions.

•The module is considered to be in compliance with UL1703 only when the module in mounted in the manner specified by the mounting instructions below.

•The solar module may be mounted by using the following methods: (*Torque:8~12Nm )

•When installing modules in heavy snow areas, special care should be taken to install the modules in a manner that provides sufficient design strength while meeting local code requirements.

Mounting by using frame bolts holes

•Secure the solar module to the structure by using the factory mounting holes.

•Four M6 stainless steel bolts, four nuts, four spring washers, and eight flat washers are recommended per solar module.

•The module may be fastened to a support by using both the outer and inner bolt holes of the frame.

•Each module should be securely fastened at a minimum 4 points on two opposite sides.

•Specific information on the solar module dimensions and location of mounting holes is provided in ‘Product Specifications’.

Module frame

Bolt

Flat washer

Flat washer

Spring washer

Nut

Support

•Tighten the bolt securely by using the combination shown above. Place the spring washer between the Flat washer and Nut.

Mounting by using clamps

•The module may be fastened to a support by using clamps on both the long edge and the short edge of the modules.

•Specific information on the solar module dimensions and location of clamping is provided in ‘Product Specifications’.

7

Page 6 Page 8
Page 7
Image 7
LG Electronics LGXXXN1C(W)-B3 installation instructions Mounting Methods, General Information
Page 6 Page 8

LGXXXN1C(W)-B3 specifications

The LG Electronics LGXXXN1C(W)-B3 is a notable addition to the lineup of innovative climate control solutions from LG. It represents the perfect blend of efficiency, modern design, and advanced technology aimed at achieving optimal indoor comfort. With an eye towards sustainability, this model embodies the company’s commitment to promoting energy-efficient appliances that benefit both users and the environment.

At the heart of the LGXXXN1C(W)-B3 is its powerful inverter technology, which adjusts the compressor speed based on the temperature in the room. This dynamic functionality not only ensures a consistent and comfortable environment but also significantly reduces energy consumption compared to traditional units. The inverter system operates quietly, making it suitable for a variety of indoor settings including home, schools, and offices.

The model offers a cooling capacity that caters to larger spaces, ensuring that no corner of the room is left untouched during operation. Users can expect rapid cooling and effective air distribution through its strategically designed airflow systems. This ensures a more even temperature across the room, preventing hot or cold spots and enhancing overall comfort.

Additionally, the LGXXXN1C(W)-B3 integrates advanced air purification technologies that work to improve indoor air quality. Equipped with multi-stage filters, it effectively captures dust, allergens, and pollutants, providing cleaner and healthier air for individuals and families alike. The unit is further enhanced with smart features, allowing users to control settings remotely via a smartphone app. This means adjustments can be made even when no one is home, ensuring energy is used efficiently.

Moreover, the LGXXXN1C(W)-B3 boasts a sleek and modern design that fits seamlessly into any aesthetic. Its compact size and attractive finish make it a stylish choice for any room without compromising on functionality. The user-friendly interface and intuitive controls simplify operation, allowing for a seamless experience whether it's adjusting the temperature, setting timers, or utilizing energy-saving modes.

In conclusion, the LG Electronics LGXXXN1C(W)-B3 is a versatile and high-performance climate control solution, combining cutting-edge technology, user-friendly design, and energy-efficient operation. It serves as a prime example of LG's commitment to excellence in home appliances, delivering comfort and reliability all year round. Whether for residential or commercial use, this model is poised to meet diverse cooling needs while maintaining a focus on sustainability.
Top Page Image Contents