Liebherr 7082 300-03 manual Instructions for installation and modification, Dimensions

3 kitchen unit side panel

4 wall

Instructions for installation and modification

Dimensions

The external dimensions of the appliance can be seen on

fig. S and in the table below.
Gross capacity	External dimensions			[mm]
of appliance [l]	A	B	C D	E	F
(see type plate)

162(18..) 1250 600 631 614 644 1179

200(21..) 1447 600 631 614 644 1179

238(25..) 1644 600 631 614 644 1179

276(28..) 1841 600 631 614 644 1179

188(20..) 1250 660 683 662 704 1287

233(24..) 1447 660 683 662 704 1287

279(29..) 1644 660 683 662 704 1287

324(33..) 1841 660 683 662 704 1287

Installation instructions

- Do not install the appliance directly next to another refrig- erator or freezer. This is important to prevent condensa- tion and consequential damage resulting from it.

-This does not apply to Side-by-Side models (SBS). They are designed for Side-by-Side installation with another refrigerator/freezer.

The "Installation instructions for Side-by-Side combina- tions" are supplied in the accessories bag for the SBS freezer or the appliance with a freezer compartment.

hexagon socket on the open-ended spanner provided (spanner width 5).

-Fit covers 8 again: insert hinge-side cover by sliding outwards and click into position; insert handle-side cover by sliding inwards and click into position.

-Bottom: Using a screwdriver, remove the spacer bo and replace on the other side.

WRe-attach the door:

-Remove plugs bp from the door mounting points and replace on the other side.

-Suspend door with spacer in hinge pin 7, close door.

-Rotate hinge component 4 by 180°, remove hinge pin 5, turn by 180° and replace. Mount both parts in the hinge bq:

slide the pin into the door mounting through the hinge, tilt in the hinge component, slide up and attach with screw 3.

WAlign the door flush with the body of the appliance using the slot on the hinge bq, then tighten screw 3.

WAttach the plinth panel 1 and click into place by pressing.

WWith the door open, insert the cover 2 in the plinth panel at the front and click into place at the back.

WTransfer* door handle br and plugs bt. With the door open, carefully lift out the pressure plates* bs at the front and slide away; unscrew handle.

Re-assemble in reverse order: replace the pressure plates and click into position.

Changing over door hinges

On appliances which are intended for individual installation the door hinges can be changed from one side to the other. On SBS appliances in stainless steel finish, which are de- signed for Side-by-Side installation, the door hinges must not be transferred to the other side!

WOnly change over door hinges when mains plug is dis- connected!

WFig. T. With the door open, lever out plinth panel 1 on the hinge side with a screwdriver and remove from front.

-Lever out cover 2 with a screwdriver. Close door.

-Unscrew screw M5 3.

WPull hinge component 4 with hinge pin 5 out from un- derneath and remove.

WOpen door, lift out at bottom and remove; do not lose the spacer bl.

WTransfer all hinge components onto the other side:

WTop: depending on version, proceed as follows:

Version I (visible operating panel): Lever out covers 8 with a screwdriver at the front and remove at an angle from below. Remove hinge pin 7 and insert on the op- posite side. Use the hexagon socket on the open-ended spanner provided (spanner width 5). Fit covers 8 again: insert at rear and click into place at front.

Version II (concealed operating panel): Lift up cover 8 on handle side, push outwards; lift up cover on hinge side and pull off.

-Unscrew earthing plate cm: first earthing screw cl, then inner retaining screw cq.

-Unscrew hinge 9: first undo earthing screw cl, then re-

taining screws cq. Fit hinge 9 to opposite side: for easy assembly, fit hinge from above and first tighten with the upper retaining screw cq M5, then screw cq and finally earthing screw cl M4.

-Turn earthing plate cm through 180° and screw tight again on the new handle side: first retaining screw cq, then earth- ing screw cl.

-Insert hinge pin 7 in the other retaining hole. Use the

Insertion into row of kitchen units

Fig. U. 600 mm appliances can be installed in a row of kitchen units. To adapt the height of the appliance to the surrounding furniture a top unit 1 can be added.

A gap of at least 50 mm depth must be provided behind and along the entire width of this unit so as to ensure sufficient ventilation. The area of ventilation underneath the ceiling should be at least 300 cm2. The greater the area the more economically the appliance will run.

WWhen installing with standard kitchen units (max. depth 580 mm) and decor panels of max. 2 mm thickness, the appliance can be set up right next to the kitchen unit.

The door protrudes 34 mm from the side of the kitchen unit and 51 mm at the front. This enables it to be opened and closed without difficulty.

WWhen setting up the appliance next to a wall 4, a mini- mum distance of 36 mm must be provided on the hinge side between the appliance and the wall (for the handle when the door is open).

1 top unit

2 refrigerator/freezer

20 * Depending on model and options GN/SGN/es..6