Life Fitness 435101 manual 318 IN. LOCKNq.JT. Parts are Fromstep

NOTE:

NOTE:

1.

IF THE REAR SHROUD IS ASSEMBLEDTO THE PARABODY425, IT WILL NEED "]70 BE REMOVEDTO ASSEMBLE THE LEG PRESS AND THE ADAPTER KIT. PLEASE REMOVETHE SE[ROUD AT THIS TIME BY REMOVINGTHE FOUR (4) 3/8 X 1 IN. BOLTS ANDFOUR 3/8 IN. WASHERS.

THE LEG PRESS ATTACHMENT(832101) MUST BE ASSEMBLED BEFORE ASSEMBLING IT TO THE PAKABODY425. PLEASE ASSEMBLE THE LEG PRESS ATTACttMENT AT TIIIS TfME USING THE 832 PRODUCT ASSEMBLY INSTRUCTIONS.

Attach O, vo (2) 2 SQ. IN. COVERCAPSonto the FRONTLEGWELDMENTas shown on drawing.

Removetwo (2) I/2 FN'. LOCKNUTSand two (2) 1/2 IN. WASHERSFROMthe PRESSBASE:\ 13ASEconnection of the 425.

SECURELYassemble the BASECONNECTIONWELDMENTto the PRESS IIASE and BASF, connection of the -12S using the two (2) I12 IN. LOCKNUTSREMOVEDIN STEP

o

SECURELYattach the assembled 832 LEG PRESS ATTACHMENTto the FRONTLEG ~rELDMENTusing two (2) I/2 X 3 IN. BOLTS,two (2) I/2 IN. WASHERS(~To, OMS'['EP2) and two (2) I/2 IN. LOCKNUTS.

SECURELYattach the 832 to the 425 by connecting the FRONTLEG WELDMENTto the BASE CONNECTION WELDMENT,using two (2) I/2 X 3. IN. BOLTS,two (2) 112 IN. WASHERSand two (2) I/2 IN. I_,OCK

Remove one (I) 1/4 .IN. CAPNUTfrom the rear L-hook of the TOP BOOM(LEAVE.2 IN. PULLEYONL-HOOK)

Assembleone (I) 2 IN. PULLEYto the rear L-hook and secure place ~vith one (I) 114 IN. CAP

CAREFULLYremove one (I) 318 IN. LOCK~ and one (I) SWIVELWITH MULTI-PRESSSHOCKCORDfrom rear fiat of the BASE.

o

I0.

11.

12.

Removeone 3/8 IN. NUT,one (I) 2-3/8 IN. CABLERETAININGCLIP, one (1) 3-I/2 X 1 IN. PULLEY,one (1) Y/8 1/2 IN BOLT,and one (1) 3/8 IN. WASHERfrom the rear flat ofthe BASE.

Reassemble one (I) 3-112 x I IN. PULLEY,one (I) 2-318 IN. CABLERETAININGCLIP, one 318 WASI-IF_R,and one

(I)318 IN. NUT,from Step 9 to the rear fiat of the BASEusing one (I) 318 x 4-I/2 IN. THREADEDSTUD,and one (1)

318 IN. NLIT.

Reassemble one (1) SWIVELWITHMULTI-PRESSSHOCKCORDto the 3/8 X 4-1/2 IN. TI-tl~AI)ED STUD,using

(I)318 IN. LOCKNq.JT. (PARTS ARE FROMSTEP 8)

Assembleone (1) 3-1/2 x I IN. PULLEYto the flat facing the leg press on the BASE,and one (1) 3-1/2 IN. PULLEYto the fiat on the FRONTLEGWELDM'ENTusing two (2) 3/8 x 2 iN. BOLTS,two (2) 3/8 IN. WASHEt~,two {2) 2-3/8 CABLERETAININGCLIPS, and taro (2) 3/8 IN. LOCKNUTS.

13.To assemble the LEGPRESSCABLE,follow lhe cable muting diagram and use the following steps:

Adjust the LEGPRESSso the seat is in its tightest pre-stretch position.

SECURELYattach the loop end of the LEGPRESSCABLEto the FROIqr LEGWELDMENTusing one (I) QUICK DISCONNECTLINg<.

~un the cable through the hole in the D-RINGas showa in ('DETAILA) and attach one {'I) KEYHOLECLEVIS to the end of the LEGPRESSCABLE.

12F21/95