10. Position the right end of the ERGO FRONT CROSSBAR (#4) near the
large access hole on the inside of the RIGHT UPRIGHT HANDLEBAR
BRACKET (L).
Align the ERGO FRONT CROSSBAR MOUNTING HOLES with those in
the RIGHT UPRIGHT HANDLEBAR BRACKET and secure using two
BOLTS (#19), from the inside of the treadmill, and NUTS (#22). Tighten
the BOLTS securely. Insert one SCREW (#16) from under the RIGHT
UPRIGHT HANDLEBAR BRACKET. Tighten the SCREW securely.
11. Position the left end of the ERGO FRONT CROSSBAR (#4) near the
large access hole on the inside of the LEFT UPRIGHT HANDLEBAR
BRACKET (N).
(Models 97Ti and 95Ti Only) Feed the SMART STOP CABLE (O) and
HEART RATE CABLE (P) into the access hole downward out the bottom
of the LEFT UPRIGHT HANDLEBAR BRACKET.
Align the crossbar mounting holes with those in the LEFT UPRIGHT
HANDLEBAR BRACKET and secure using two BOLTS (#19), from the
inside of the treadmill, and NUTS (#22). Tighten the BOLTS securely.
Insert one SCREW (#16) from under the LEFT UPRIGHT HANDLEBAR
BRACKET. Tighten the SCREW securely.
NOTE: BE CAREFUL NOT TO PINCH THE SMART STOP CABLE (O)
AND HEART RATE CABLE (P) (IF EQUIPPED) WHEN ASSEMBLING
THE ERGO FRONT CROSSBAR (#4) TO THE LEFT UPRIGHT
HANDLEBAR BRACKET.
(Models 97Ti and 95Ti Only) Feed the SMART STOP CABLE (O) and
HEART RATE CABLE (P) upward through the top of the LEFT UPRIGHT
(#1).
12. Slide the LEFT INSIDE HANDLEBAR SHROUD (#5) near the LEFT
UPRIGHT HANDLEBAR BRACKET (N).
(Model 93T Only) Position the HANDLEBAR GROMMET (#27) at the end
of the LEFT INSIDE HANDLEBAR SHROUD. Install the HANDLEBAR
GROMMET onto the inside edge of the LEFT INSIDE HANDLEBAR
SHROUD as shown.
Locate and position the LEFT OUTSIDE HANDLEBAR SHROUD (#7) to
match the LEFT INSIDE HANDLEBAR SHROUD.
(Model 93T Only) Install the remaining portion of the HANDLEBAR
GROMMET onto the LEFT OUTSIDE HANDLEBAR SHROUD as it is
positioned to match the LEFT INSIDE HANDLEBAR SHROUD.
Secure the SHROUDS together using three SCREWS (#15). Tighten the
SCREWS securely. Do not overtighten the SCREWS. Repeat the
procedure for the RIGHT INSIDE and OUTSIDE HANDLEBAR SHROUDS
(#6 and #8).
13. Locate the DISPLAY CONSOLE (#9). Remove the eight SCREWS (Q) from
the back of the DISPLAY CONSOLE and separate the front of the DISPLAY
CONSOLE from the rear. Position the REAR CONSOLE (R) over the LEFT
and RIGHT TOP MOUNTING PLATES (H & J) as shown. From the bottom
of the LEFT and RIGHT TOP MOUNTING PLATES, secure the REAR
CONSOLE using four screws (#17). Tighten the SCREWS securely. Do not
overtighten the SCREWS.
14. Position and rest the FRONT CONSOLE (S) facedown across the
HANDLEBARS (#3). Connect all CONNECTORS leading from the LEFT (if
equipped) and RIGHT UPRIGHTS (#1 & #2) to the corresponding
CONNECTORS located on the FRONT CONSOLE. Feed any excess WIRE
HARNESS into the UPRIGHTS. Carefully route all WIRE HARNESSES
through the WIRE HARNESS GUIDES (T) located at the lower left of the
REAR CONSOLE (R)
15. Tilt the FRONT CONSOLE (S) upright and in position over the REAR
CONSOLE (R). Secure the FRONT CONSOLE to the REAR using the
previously removed eight SCREWS (Q). Tighten the SCREWS securely. Do
not overtighten the SCREWS.
NOTE: BE CAREFUL NOT TO PINCH THE ANY CABLES WHEN
ASSEMBLING THE FRONT CONSOLE (S) TO THE REAR CONSOLE (R).
17
H
J
S
7
5
R
8
Q
6
15
N
3
3
2
1
9

R

1

T

26
526
4
19
L22
22
17
17
3
6
1
2
M
3
O
P
N