Life Fitness 97TE manual Bracket L, Bracket N, Handlebar Bracket, Rear Console R

9.	Position the right end of the ERGO FRONT CROSSBAR (#4) near the			M 6
				5
	large access hole on the inside of the RIGHT UPRIGHT HANDLEBAR
	BRACKET (L).			26
	Align the ERGO FRONT CROSSBAR MOUNTING HOLES with those in
	the RIGHT UPRIGHT HANDLEBAR BRACKET and secure using two			19
	BOLTS (#19), from the inside of the treadmill, and NUTS (#22). Tighten
	the BOLTS securely. Insert one SCREW (#16) from under the RIGHT	O		4
	UPRIGHT HANDLEBAR BRACKET. Tighten the SCREW securely.		P
10.	Position the left end of the ERGO FRONT CROSSBAR (#4) near the
				N
	large access hole on the inside of the LEFT UPRIGHT HANDLEBAR		22
	BRACKET (N).			2
	Feed the SMART STOP CABLE (O) and HEART RATE CABLE (P) into
	the access hole downward out the bottom of the LEFT UPRIGHT	1		17
	HANDLEBAR BRACKET.

Align the crossbar mounting holes with those in the LEFT UPRIGHT HANDLEBAR BRACKET and secure using two BOLTS (#19), from the inside of the treadmill, and NUTS (#22). Tighten the BOLTS securely. Insert one SCREW (#16) from under the LEFT UPRIGHT HANDLEBAR BRACKET. Tighten the SCREW securely.

NOTE: BE CAREFUL NOT TO PINCH THE SMART STOP CABLE (O)

AND HEART RATE CABLE (P) (IF EQUIPPED) WHEN ASSEMBLING

THE ERGO FRONT CROSSBAR (#4) TO THE LEFT UPRIGHT

HANDLEBAR BRACKET.

Feed the SMART STOP CABLE (O) and HEART RATE CABLE (P) upward through the top of the LEFT UPRIGHT (#1).

11. Slide the LEFT INSIDE HANDLEBAR SHROUD (#5) near the LEFT UPRIGHT HANDLEBAR BRACKET (N).

Locate and position the LEFT OUTSIDE HANDLEBAR SHROUD (#7) to match the LEFT INSIDE HANDLEBAR SHROUD.

Secure the SHROUDS together using three SCREWS (#15). Tighten the SCREWS securely. Do not over-tighten the SCREWS. Repeat the procedure for the RIGHT INSIDE and OUTSIDE HANDLEBAR SHROUDS (#6 and #8).

12.Locate the DISPLAY CONSOLE (#9). Remove the eight SCREWS (Q) from the back of the DISPLAY CONSOLE and separate the front of the DISPLAY CONSOLE from the rear. Position the REAR CONSOLE (R) over the LEFT and RIGHT TOP MOUNTING PLATES (H & J) as shown. From the bottom

of the LEFT and RIGHT TOP MOUNTING PLATES, secure the REAR	R
CONSOLE using four screws (#17). Tighten the SCREWS securely. Do not
over-tighten the SCREWS.	J
13. Position and rest the FRONT CONSOLE (S) facedown across the
HANDLEBARS (#3). Connect all CONNECTORS leading from the LEFT (if
equipped) and RIGHT UPRIGHTS (#1 & #2) to the corresponding	H
CONNECTORS located on the FRONT CONSOLE. Feed any excess WIRE
HARNESS into the UPRIGHTS. Carefully route all WIRE HARNESSES
through the WIRE HARNESS GUIDES (T) located at the lower left of the	5
REAR CONSOLE (R)
	17
14. Tilt the FRONT CONSOLE (S) upright and in position over the REAR
CONSOLE (R). Secure the FRONT CONSOLE to the REAR using the	N
previously removed eight SCREWS (Q). Tighten the SCREWS securely. Do	7
not over-tighten the SCREWS.	15

NOTE: BE CAREFUL NOT TO PINCH THE ANY CABLES WHEN	3
ASSEMBLING THE FRONT CONSOLE (S) TO THE REAR CONSOLE (R).
	2

T

1

26

L 22

3

17

3

9 S

Q

8

6

3

R

1