READ AND UNDERSTAND ALL TRACK, CONNECTOR, FEED-IN-KITS, AND ACCESSORY

INSTRUCTION SHEETS BEFORE INSTALLING ANY PROSPEC™ TRACK ITEM.

This fixture is intended for installation in accordance with the National Electrical Code and local or Federal code specifications. To assure full compliance with codes and regulations, check with your local electrical inspector before installation. To prevent electric shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

INSTRUCTION SHEET NO.

IS:26646

A0397

Page 1 of 2

Recessed Power Extension Connector for use with Recessed ProSpecTrack System Only.

The Power Extension Connector allows power to be jumped from one track, around or through structural obstacles, to another track unit. It replaces the Dead End Cover at the end of a Feed Track unit or a run of track units. Power can be fed into or removed from the Recessed Power Extension Connector by using any of the power feed-in kits available for Recessed ProSpec Track. A few examples are shown on the reverse side.

Caution:

Turn off power at fuse box before installing the Recessed Power Extension Connector and track.

Instructions for grounding must be followed. Failure to do so may result in a hazardous condition.

Use only #12 ga. solid copper wire in connectors to maintain proper track rating.

Observe polarity, white (neutral) wire must be connected to terminal marked "NEUT". Failure to observe Polarity may result in an electrical hazard.

Do not use Track as a conduit support. Independent conduit supports (such as suitable conduit straps) must be used to attach the conduit installation to the building structure.

INSTALLING CONNECTOR INTO TRACK SECTION--Fig.1 & Fig. 2

1.Remove Dead End Cover if necessary by pulling it out of the track (save Dead End cover).

2.Push connector into the track until there is no gap between the track unit and connector. Ensure that the contact blades are aligning with the copper wires in the track during assembly.

3.Tighten the locking screw.

4.Tighten Spline Screws.

POWER FEED TO THE CONNECTOR(S)

DIRECT FEED FROM ABOVE CEILING--Fig.3

1.Remove the bottom cover (if required) by snapping it out of the connector. Save cover.

2.Remove K.O. plate from the connector.

3.Remove the K.O..

4.Attach the electrical connector onto the K.O. plate using the nut provided. Align the electrical connector such that the connector is hidden by the track width.

5.Attach the K.O. plate onto the connector using the screw that was previously removed.

6.Pass cable or conduit through electrical connector and clamp cable or conduit to electrical connector.

7.Form the wires to the appropriate screw terminals. Cut and strip wires and attach to the screw terminals. (See wiring section of instruction sheet).

8.Snap the bottom cover onto the connector.

Track Unit

Connector

Bottom Cover

Dead End

Track Unit

Fig. 1

Spline Screw

Track Unit

Locking Screw

Fig. 2

Electrical

Conduit or Cable

(by Others)

Connector

(by Others)

 

 

K.O. Plate

Knock Out

Dead End

 

Nut

 

 

Track Unit

Fig. 3

Bottom Cover

 

FALL RIVER, MASSACHUSETTS 02720

MONTREAL, QUEBEC, CANADA

© 1997

Page 1
Image 1
Lightolier instruction sheet IS26646, Retain these instructions for maintenance reference, A0397

26646 specifications

The Lightolier 26646 is an exemplary model in the realm of modern lighting solutions, known for its blend of innovative design, functionality, and energy efficiency. This fixture is ideal for both residential and commercial applications, offering versatility and style that can complement various interior aesthetics.

One of the key features of the Lightolier 26646 is its sleek, minimalist design. This fixture is designed to fit seamlessly into a range of environments, from contemporary spaces to more traditional settings. Its clean lines and unobtrusive silhouette make it a popular choice for homeowners and designers alike, allowing for integration into any room without overwhelming the existing décor.

In terms of technology, the Lightolier 26646 incorporates advanced LED lighting. LED technology not only contributes to energy efficiency but also offers a longer lifespan compared to traditional bulbs. The fixture provides consistent and vibrant illumination, enhancing overall space ambiance while significantly reducing electricity costs. The color temperature of the LED light can also be tailored to meet specific preferences, making it easy to create the perfect atmosphere for any occasion.

Another notable characteristic of the Lightolier 26646 is its easy installation and adaptability. The fixture is designed with user convenience in mind, often featuring simple mounting options and compatible hardware that allows for quick and hassle-free setup. Moreover, the Lightolier 26646 can be integrated with dimmer switches, giving users control over brightness levels and allowing for a customizable lighting experience.

Safety and durability are additional attributes that enhance the Lightolier 26646's appeal. Constructed with high-quality materials, the fixture is built to withstand the rigors of daily use, ensuring longevity without compromising aesthetic value. The design also prioritizes safety, with elements designed to minimize heat output and reduce the risk of overheating, particularly important in enclosed spaces.

In conclusion, the Lightolier 26646 combines sophisticated style, cutting-edge technology, and practical features, making it a standout choice in the lighting market. Whether upgrading home lighting or designing a new commercial space, this fixture offers a reliable, efficient, and aesthetically pleasing solution that meets diverse lighting needs.