Lightolier 9147 instruction sheet Is, Surfacefeedconnector, Foruse With Profiletracksystem Only

,

READAND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

“his fixture is intended for installation in accordance with the National Electrical Code and local regulations. “o assure full compliance with local codes and regulations, check with your local electrical inspector before wtallation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

T

INSTRUCTION SHEET NO.

IS:9147

Retain these instructions for maintenance reference. 0395 Page 1 of 1

SURFACEFEEDCONNECTOR

FORUSE WITH PROFILETRACKSYSTEM ONLY

WARNING:

●TURN OFF POWER AT FUSE BOX BEFORE INSTALLING ELECTRICAL CONNECTOR AND TRACK.

●DO NOT USE ELECTRICAL CONNECTOR AS A CONDUIT SUPPORT. INDEPENDENT CONDUIT SUPPORTS (SUCH AS

CONDUIT STRAPS) MUST BE USED TO ATTACH THE CONDUIT INSTALLATION TO THE BUILDING STRUCTURE.

. OBSERVE POLARITY; WHITE NEUTRAL WIRE MUST BE CONNECTED TO THE TERMINAL MARKED “NEUT” IN THE ELECTRICAL CONNECTOR.

. USE 12 GA. OR 14 GA. SOLID WIRE IN ELECTRICAL CONNECTOR ONLY.

		— .
A. INSTALLING SURFkCE FEED CONNECTOR.		~/; —	j,
		/,/
1.Point	the POLARITY TAB away from the BEAD ON the track.	,,,	‘
		\\\
2, Insert	SURFACE FEED CONNECTOR into track. Ensure CONTACT	b<!—.~
		—

BLADES insert into the GAP of the TRACK COPPER CONDUCTOR.

3.Tighten LOCKING SCREW.

B.DIRECT POWER FEED USING SURFACE CONDUIT.

1.Remove BO~OM COVER by removing SCREW (retain).

2.Remove PLASTIC TAB from BOTTOM COVER.

3.Screw the ELECTRICAL FITTING into the METAL PI-ATE of the Surface Feed Connector.

4.Pass Supply LEAOS through ELECTRICAL FITTING and secure conduit to ELECTRICAL FITTING.

5.Strip and form Supply LEADS to fit into SURFACE FEED CONNECTOR. Fasten Supply LEADS to SCREW TERMINALS; NEUTRAL (WHITE) LEAD to terminal marked “NEUT”. GROUND LEAD to TERMINAL marked “GND”. HOT (BLACK) LEAD to

BRASS SCREW.

6.Fasten BOTTOM COVER to SURFACE FEED CONNECTOR using

C. DIRECT POWER FEED FROM ABOVE CEILING

1.Remove BOTTOM COVER by removing SCREW (retain).

(BYOTHERS)

THROUGH CE!LING FEEO

Lg

~

SURFACE FEEOI

SCREW.

~

-NEUTRAL SUPPLY

! WIRE (WHITEi ~ LOCKING SCREW

CONTACT BLAOE

,. TRACK

BEAO

~

2.Remove Knock Out from METAL PLATE.

3.Secure ELECTRICAL FITTING TO MEAL PLATE using the NUT provided.

,,———— ——

\

/

(c b, L —-— .:

NOTE: Special care must be taken when making the hole in the mounting surface to prevent the hole from being visible when the track is mounted. The screws

“- ~~d=..

(~:~p:--

“ —.

‘~~--

,(3T f—.— -- -—

on the ELECTRICAL FllllNG may have to be cut to conceal the mounting hole.

4.Follow instruction 4, 5 and 6 above.

-~’/---.-=>._-, ~.–

,’––-. .—.

/—HOT SUPPLYWIRE

-F”---

-SUPPLYWIRE(BLACK)

::$~ “–-

w—--- ~—z::

-POLARllYTAB

~

D. POWER FEED FROM STEM KIT

1.Remove BOTTOM COVER by removing SCREW.

2.Remove KNOCK OUT from the TOP METAL PLATE.

3.Pass SUPPLY LEADS through KNOCK OUT HOLE.

4.Follow instructions 5 and 6 above.

GROUNO		?,	>,		—–-	7/16STRIP
		c				SUPPLYWIRE
	p	~;”,		~ —	________	--
		-.	/	--.-——–––-

YCH

‘lWO WIRES MAY BE ATTACHEO I

@ FALL RIVER MASSACHUSETTS, 02720

l-I c> 1+ ~c>lm I 1= 1? MON::::::;EC, CANADA