READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FlfiURE
“his fixture is intended for installation in accordance with the National Electrical Code and local regulations. ‘o assure full compliance with local codes and regulations, check with your local electrical inspector before nstallation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
INSTRUCTION SHEET NO.
IS:9196
Retain these instructions for maintenance | reference. | 0395 | Page 1 of 1 |
|
|
T-BAR LIVE END
FOR USE WITH PROFILE, TRACK SYSTEMS ONLY
WARNING:
●TURN OFF POWER AT FUSE BOX BEFORE INSTALLING ELECTRICAL CONNECTOR AND TRACK.
c DO NOT USE ELECTRICAL CONNECTOR AS A CONDUIT SUPPORT. INDEPENDENT CONDUIT SUPPORTS (SUCH AS CONDUIT STRAPS) MUST BE USED TO AllACH THE CONDUIT INSTALLATION TO THE BUILDING STRUCTURE.
●OBSERVE POLARITY; WHITE NEUTRAL WIRE MUST BE CONNECTED TO THE TERMINAL MARKED “NEUT” IN THE ELECTRICAL CONNECTOR.
●USE 12 OR 14 GAUGE SOLID WIRE IN ELECTRICAL CONNECTOR ONLY.
NOTE: Special care must be taken when making the hole in the mounting surface to prevent the hole from being visible when the track is mounted. The screws on the ELECTRICAL FITTING may have to be cut to conceal the mounting hole.
A. INSTALLING SURFACE FEED CONNECTOR
1.Point the POLARITY TAB away from the BEAD on the track.
2.Insert SURFACE FEED CONNECTOR into track. Ensure CONTACT BLADES insert into the TRACK CONDUCTOR GAPS.
4. Tighten LOCKING SCREW.
ELECTRICALFITTING
!?**OR
B. DIRECT POWER FEED.
1.Remove BOTTOM COVER by removing SCREW (retain).
2.Remove one K,O,
3.Attach the ELECTRICAL FITTING onto the METAL PLATE
4.Mount TRACK ASSEMBLY to
(SOLD SEPARATELY),
5.Pass Supply LEADS through ELECTRICAL Fl~lNG and secure conduit to ELECTRICAL Fl~lNG.
6.Strip and form Supply LEADS to fit into SURFACE FEED CONNECTOR, Fasten Supply
&>*
LEADS to SCREW TERMINALS; NEUTRAL
(WHITE) LEAD to terminal marked “NEUT”p~~~, GROUND LEAD to TERMINAL marked “GND”,
HOT (BLACK) LEAD to BRASS SCREW.
7, Fasten BOTTOM COVER to SURFACE FEED CONNECTOR using SCREW.
\
,F=~Q
BOTTOM COVER
,. . ... .... ..!.5/
SCREW
-ELECTRICALFl~lNG V’
) (ByOTHEPS) ‘
/
/‘+
.
*
* |
|
|
|
|
|
|
|
|
|
| |||
| / . | ~~;- |
| |||
\ |
|
| * |
| ||
~~~~& |
|
|
| |||
‘k’+ |
| ‘: | ‘: | : | – | |
|
| J- |
|
| ||
‘a, | ,, | / |
|
|
|
|
‘d> | ~;:fRITy |
|
| r | ||
|
|
|
|
|
| TRACK — |
Y |
|
|
|
|
| BEAD |
|
|
|
|
|
| |
/ |
|
|
|
|
|
|
|
| 4 |
| w | 7/16” | |
‘~> |
|
|
| |||
P | ~.._— |
|
|
| STRIP | |
|
|
| SUPPLY | |||
g> |
|
|
|
|
| |
/iL/ |
|
|
|
|
| WIRE |
TWO WIRES MAY BE ATTACHED
TO ONE SCRE’AJTERMINAL
@ FALL RIVER, MASSACHUSETTS, 02720
1.1 | C> | I+ | TC>I. | I 1: | 1? | MONTREAL, | QUEBEC, | CANADA |
d
