Lightolier C7055, D7707, C7709 instruction sheet ISA7053, Frame-In Fig, Snafin FIG, Push-In Fig

,										INSTRUCTION SHEET NO.
	INSTALLATION OF CALCULITE REFLECTOR TRIMS									IS:A7053
		INSTRUCTION SHEET FOR ITEMS:
A7053,	A7701,	A7058,	B7054,	B7705,	B7760,	B7780,	C7055,	C7709,	D7707
										0888

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE lNSIALLING FIXTURE.

This fixture is intended for installation in accordance with the National Electrical Code and local or federal code specifications. To prevent electrical shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

g	4?’’’’”		m
FIG. 1		FIG. 2	FIG. 3
A. FRAME.IN		B. SNAP.IN	C. PUSH.IN

WARNING+RISK OF FIRE)DO NOT INSTALL INSULATION WITHIN 3 INCHES OF FIXTURE SIDES OR

WIRING COMPARTMENT, NOR ABOVE FIXTURE IN SUCH A MANNER SO AS TO ENTRAP HEAT.

A. FRAME-IN (FIG. 1)

See Frame-In-Kit Instruction Sheet (No. IS:A400) for installation procedure.

B.SNAFIN (FIG. 2)

NOTE:For Overlapping Trim installation slip WHITE TRIM RING on over OPTICAL SECTION, as shown on Fig. 4 and 5, before Snap-in. For Flangeless Trim installation, WHITE TRIM RING is not required.

Fasten ADJUSTABLE SOCKET HOUSING to OPTICAL SECTION (reflector or baffle by: (1) aligning the SPRING with CUTOUT on top (Fig. 6); (2) pushing ADJUSTABLE SOCKET HOUSING onto OPTICAL SECTION for engagement. If S.LOTS are provided on OPTICAL SECTION for vertical adjustment, engage

—SPRING to desired Iamplwattage position (see label on inside and outside to neck of REFLECTOR/HOUSING). See Fig. 6 and 7.

opl,:,&	“Q
SECTION	FIG. 5
FIG. 4
		CUT OUT
		NTOP

LAM PIWATTAGE

mPOSITION LABEL

\(INSIDE NECK)

/

LAM P/WATTAGE POSITION LABEL (OUTSIDE NECK)

FIG. 6

C. PUSH-IN (FIG. 3)

Push OPTICAL SECTION straight up into MOUNTING FRAME until tight against finished ceiling. RETAINING SPRINGS on MOUNTING FRAME (Fig. 1) will secure OPTICAL SECTON (reflector or baffle) in place.

NOTE: To remove OPTICAL SECTION, use FINGER HOLE (Fig. 7) provided on upper part for sure grip;

turn OPTICAL SECTION counterclockwise while pulling downward. After starting, use both hands to remove. See Fig. 8.

CARE AND MAINTENANCE OF “A12AK” REFLECTOR

If handling of reflectors with anodized or Alzak finish is required, the use of clean white or plastic film gloves is recommended to avoid fingerprints.

:edzeg or Alzak surfaces can be cleaned by the following

1.Wipe of with a soft, clean, dry, lint-free cloth.

2.Wipe off with a clean cloth dampened in mild detergent solution. Rinse, then wipe dry with lint-free cloth or paper towel.

3.Wipe off with a clean cloth dampened with a solution of wetting agent and water (such as 2 oz. per gallon “Pluronic L62-LF by Wyandotte Products), or a liquid wax such as Glass Wax@. Then wipe dry. Avoid gritty cleaning agents.

SPRINGS FIG. 7

TO REMOVE

FIG. 8

W.Pat. No. 4,039,822

L I <H-n-c> M E la” ;V:::::L,N::EV::, E;A::::