Lightolier Dorm Lyte Page 2 of, Ordering Information, Options/Accessories, Specifications, Type

Section 4A/Folio I60-10

Wall Mounted Fluorescent Dorm Lyte

Page 2 of 2

6" Width, 48" Nominal Length 1 or 2 Lamp T5 or T8

Model No. DL4X232120SO

LER = FP - 58.6 IW - 53.1 BF - 0.88 Comparative yearly lighting energy cost per

1000 lumens = $4.10

Report Number: G2006054

Lamp: F32T8

Luminaire: Up/down Wall Mounted with Two Color Co-extruded Lens

Ballast: B232IUNVHP-B

Report is based on 2950 Lumens per lamp.

Efficiency: 60.4%
CIE Type-Direct-Indirect
Plane:				0-Deg		90-Deg 180-Deg.
Spacing Criteria:					1.9		1.1		1.1
Shielding Angles:					55		65
Luminous Length: 48.000						2.400
Height of Side				6.000		6.000
COEFFICIENTS OF UTILIZATION –
ZONAL CAVITY METHOD. EFFECTIVE
FLOOR CAVITY REFLECTANCE 0.200
RC		80			50			30
RW	70	50	30	50	30	10	50	30	10
01	58	54	52	42	40	38	34	33	32
02	52	47	43	36	33	31	29	27	25
03	47	41	36	31	28	25	26	23	21
04	43	36	31	28	24	21	23	20	18
05	39	32	27	25	21	18	20	17	15
06	36	28	23	22	18	16	18	15	13
07	33	26	21	20	16	14	16	14	12
08	31	23	18	18	15	12	15	12	10
09	29	21	16	17	13	11	14	11	99
10	27	19	15	15	12	10	13	10	88

LUMINANCE DATA IN CANDELA/SQ. METER

AVERAGE AVERAGE AVERAGE AVERAGE

IN DEG.	0-DEG.	45-DEG. 90-DEG.
45	10652.	1310.	3855.
55	12396.	862.	3044.
65	014783.	540.	2384.
75	019419.	277.	1701.
85	032024.	73.	635.

CANDELA DISTRIBUTION0
	0.0	45.0	90.0	FLUX
0	465	465	465
5	479	455	455	44
15	531	425	420	126
25	581	375	368	190
35	615	311	301	237
45	630	241	228	261
55	623	168	153	254
65	589	108	95	235
75	548	55	48	203
85	504	14	10	172
90	496	12	0
95	514	32	13	184
105	558	77	55	223
115	598	132	107	257
125	623	195	170	278
135	630	261	237	278
145	615	326	304	252
155	581	384	365	201
165	531	425	412	128
175	470	446	442	43
180	448	448	448

ZONAL LUMEN SUMMARY

ZONE	LUMENS	% LAMP	% FIXT
00-030	359	6.1	10.1
00-040	596	10.1	16.7
00-060	1112	18.8	31.2
00-090	1723	29.2	48.3
90-120	664	11.3	18.6
90-130	942	16.0	26.4
90-150	1472	25.0	41.3
90-180	1843	31.2	51.7
00-180	3566	60.4	100.0

Room Size:	12' x 10' x 8' Ceiling.
Reflectance:	80-50-20 .80LLF
Reading Area:	35-40fc

1'	15		35	52	35	15
3'	15		25	31	35	15
5'	12		14	16	14	12
7'	9		10	10	10	9
9'	8		8	8	8	7
11'	7		7	7	7	7
	1'		3'	5'	7'	9'
		3'

35 to 40 fc reading plane

(60° from horizontal)

5'

3'6"

Reading

Plane

reading position

Ordering Information

Explanation of Catalog Number. Example: DL4X232120SO

	DL	4
	Dorm Lytel:	Fixture	X = Up/Down Light		Lamp
Wall Mounted		Length:	R = Independent		Quantity:
	Fluorescent	4=48"		Up or Down	1=1 Lamp
				Light . (2 lamp	2=2 Lamp
				only)

Options/Accessories

Fusing: Internal fast blow fusing: SUFFIX: GLR. Internal slow blow fusing: SUFFIX: GMF.

Radio Interference Filter: 120 or 277 volt, 50 or 60 Hz. One per fixture. SUFFIX: R.

One per Ballast, SUFFIX: B.

Electronic (Low Voltage) Sequential Switch: Switch factory mounted for Up and Down Light operation from pillow switch. Includes phone jack type receptacle. SUFFIX: SW.

Momentary Button Cordset: Traditional "Winged" Pendant design ESD protection to 15,000 volts. Heavy duty 7' cable with phone plug and security clip.

Consult factory: Part number 7800W-7 CSP. (Button Cordset can only be used with SW Sequential Switch option)

4-Way Pull Switch: SUFFIX: 4P.Electrical Wiring Options: Consult factory.

Lamp Type:		Voltage:				Options:
32=32W T8	120, 277 or UNV				Add appropriate
28=28W T5	UNV=120-277				suffix to catalog
54=54W T5						no., ie: (GLR)
			Ballast	Type:	<10THD
		1 or 2 Lamp 32W Elec. T8		<20THD
				SO *	HI *
		1 or 2 Lamp 28W Elec. T5		–	PI †
		1 or 2 Lamp 28W Elec. T5		–	†PG ††
		1 or 2 Lamp 54W Elec. T5		–	†PG ††
		(Nominal 48")
		LOL T8 Dimming		PS*	–

*Instant Start Standard †Instant Start (120 or 277) ††Program Rapid Start (UNV only)

NOTE:

For T8 UNV, you must use HI Ballast Code.

Specifications (continued)

Electrical: Thermally protected class “P” ballast CBM approved, non PCB. If K.O. is within 3" of ballast, use wire suitable for at least 90°.

Labels: I.B.E.W./UL and ULc Listed.

Specifications

Materials: Chassis parts are die-formed code rolled steel. End Caps–20 gauge cold rolled steel. Refractor–1/8" thick DR acrylic, unique co-extrusion, white opaque center, linear prisms to spread up/down light.

Finish: exterior white baked acrylic enamel.

End Caps and Cover–Post painted baked white enamel, 86% reflectance. Phospate undercoating.

Job Information	Type:
Lightolier a Genlyte company	www.lightolier.com

Technical Information: (978) 657-7600 • Fax (978) 658-0595

631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710 We reserve the right to change details of design, materials and finish.

© 2006 a Genlyte company