Lightolier DPA2G12LS232 Photometry, Ordering Information, Options/Accessories, Specifications

Deepcel Plus DPA2G12LS232

Page 2 of 2

Photometry Model No. DPA2G12LS232120SO

THIS REPORT IS BASED ON PUBLISHED INDUSTRY PROCEDURES • FIELD PERFORMANCE MAY VARY FROM LABORATORY PERFORMANCE.

2' x 4' Recessed Fluorescent, 3", 12 Cell Parabolic Louver Static or Air/Return, 2 Lamp, T8 or T5

LER = FP - 64.4 IW - 61.6 BF - 0.87

Comparative yearly lighting energy cost per 1000 lumens = $3.73

coefficients of utilization — zonal cavity method

	RF		20			20			20
	RC		80			50			30
	RW	70	50	30	50	30	10	50	30	10
	1	89	85	83	80	78	76	77	75	74
ratio	2	81	76	71	71	68	64	69	66	63
	3	74	67	61	63	59	55	61	57	54
cavity	4	69	59	53	56	51	47	55	50	46
	5	63	53	46	50	45	40	49	44	40
room	6	58	48	41	45	40	35	44	39	35
	7	53	43	36	41	35	31	40	35	31
	8	50	39	32	37	32	28	36	31	27
	9	46	36	29	34	29	25	33	28	25
	10	43	33	27	32	26	22	31	26	22

visual comfort probability (VCP) average 100 fc; reflectances 80/50/20

room size				ceiling height					ceiling height
W	L		8.5	10.0	13.0	16.0		8.5	10.0	13.0	16.0
20	20		80	75	76	86		76	71	71	77
20	30		83	78	75	76		80	74	70	72
20	40		83	81	79	77		80	77	73	72
20	60		83	81	81	80		80	77	76	74
30	20		83	78	75	82		81	75	71	75
30	30		86	81	75	73		84	77	71	71
30	40		86	84	78	74		84	80	73	70
30	60		86	84	81	77		84	80	76	73
30	80	lengthwise	86	84	81	77	crosswise	84	80	76	76
40	40		86	85	80	74		84	81	76	71
40	20		83	82	78	81		81	77	75	76
40	30	luminaries	86	83	77	73	luminaries	84	79	74	71
40	60		86	85	83	77		84	81	79	73
40	80		86	85	83	77		84	80	79	75
40	100		86	85	83	77		84	80	78	75
60	30		86	84	79	75		84	79	76	74
60	40		86	85	82	76		84	81	78	73
60	60		86	85	84	78		84	80	80	75
60	80		86	85	84	79		84	80	80	76
60	100		86	85	84	79		84	80	80	76
100	40		86	85	82	78		84	80	78	74
100	60		86	85	84	80		84	80	80	77
100	80		86	85	84	81		84	80	80	77
100	100		86	85	84	81		84	80	80	77

Ordering Information

Explanation of Catalog Number. Example: DPA2G12LS232120SOCP

2 S

2

Deepcel Plus

Parabolic:

Pre-anodized

aluminum

louver

DP

DY

ND

			Number of	Louver Finish:	Single "V"
Body Style:	Fixture	Ceiling Type:
A=Air Supply	Width	G= Grid	Cells:	L = Low	Reflector
S=Static		(lay-in T bar)	12=2 rows	iridescence
		F= Flanged (over	of 6	Semi-specular
		lap) Z spline and	18=3 rows	(standard)
		plaster frame	of 6	P =Low
		T= Slot grid or	24=3 rows	iridescence
Standard Deepcel		two-directional	of 8	Specular
		concealed T	32=4 rows W =White Baked
		(see options)	of 8	Enamel

For NYC Code – I.B.E.W. Manufactured

For NYC Code – Local 3 Manufactured 5½" Deep Body

Lamp

Quantity

Lamp Type/

Fixture Length:

32=32W T8

28=28W T5

54=54W T5 (Nominal 48")

				Options:
Voltage:			Add appropriate
			suffix to catalog no.,
120, 277 or				ie: (CP)
UNV=120-277
	Ballast	Type:
			<20THD <10THD
1-2	Lamp Elec. T8		SO *	HI	*
1-2	Lamp 28W Elec. T5		–	PI	†
1-2	Lamp 28W Elec. T5		–	PG ††
1-2	Lamp 54W Elec. T5		–	PG ††
LOL T8 Dimming			PS	–

Other dimming options. Consult factory.

*Instant Start Standard

†Instant Start (120, 277 or UNV) ††Program Rapid Start (UNV only)

NOTE:I

For T8 UNV, you must use H Ballast Code.

Options/Accessories

Plaster Frame: Catalog Number: PF24.

Continuous Row Installation: For F type fixtures, half width flanges are required between

fixtures. Order Catalog Number: 2FC TRIM CSP (each joint).

Radio Interference Filter: To order one RIF per fixture; SUFFIX: R. To order one RIF per ballast;

SUFFIX: B.

Electrical Wiring Options: Consult factory.

Air Closure Strip: SUFFIX: ACS4 (factory installed).

Drywall Kit: Order Catalog Number: FK92X4. (Request Folio OA30-10 Rev. A).

Chicago Plenum: SUFFIX: CP.

Specifications

Performance: In an installation of 2 lamp 32W luminaires in a room cavity ratio of 1, reflectance 80% ceiling, 50% wall, 20% floor, the C.U. shall not be less than .85. To prevent glare the VCP shall be not less than 75 either lengthwise or crosswise (at 100fc level) and the average brightness at 65° shall not exceed 1606 candelas per square meter. To control veiling reflections, luminaire output in the 30°-90° zone shall not be less than 72.0%.

Air Handling (DPA only) side air pasaages for air supply or air return. Supply air is discharged vertically. Optional side closure strips. Air return is also provided through the lamp compartment through fixture body ends.

Materials: Chassis parts are die-formed code gauge cold rolled steel. Housing is ribbed for rigidity with side rails hemmed over and housing ends turned-in for safe handling. Louver is pre-anodized aluminum (Coilzak® or equal.

Specifications (continued)

Finish: Chassis exterior–black baked polyester enamel. Cavity–white baked polyester enamel minimum 86% reflectance. Phosphate undercoating. Louver–low iridescence semi- specular anodized vertical grain aliminum reflector sheet is standard.

Electrical: Thermally protected class “P” ballast C.B.M. approved, non PCB. If K.O. is with- in 3" of ballast, use wire suitable for at least 90°.

Labels: I.B.E.W. UL and ULc Listed.

	Job Information	Type:
Lightolier a Genlyte company		www.lightolier.com

Technical Information: (978) 657-7600 • Fax (978) 658-0595

631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710 We reserve the right to change details of design, materials and finish.

© 2007 a Genlyte company Section 2/Folio G51-40 Rev. A