Lightolier F7000-23 specifications 1BHF

PG


Lighting Systems F7000-23

1BHF

PG

'
4FSJFT
-JHIU
5
4USJQFE
8BMM
.PVOU

3.25” (8.26cm)

54

1

4.44” (11.28cm)

1.63” (4.14cm)

4.187”

(10.63cm)

1.000”

(2.54cm)

1.863”

(4.73cm)

6. Pattern Shielding

Ordering Information

FamilySeries

FW7 5

5 = Curved

Complete Ordering Instructions below.

Type

3

3 = Tiger

Striped

Lamps

1

1 = 1 Lamp

Color		Wattage	Voltage
AL = Aluminum	1	= 28W	1 = 120v
WH = White	2	= 54W	2 = 277v
	3 = 28W Dimming
	4	= 28W EM
	5 = 54W Dimming
	6	= 54W EM

Length

4= 4’ (121.92cm)

8 = 8’ (243.84cm)

Features

1.Housing: Single piece of high purity extruded aluminum, a portion from recycled material.

2.Housing End: Die-cast aluminum, welded in place.

3.End Cap: Die-cast aluminum. Encloses the end of the run.

4.Lamps: F28T5 or F54T5HO as specified. By others. Installed from the ceiling side of the luminaire.

5.Ballast: Electronic. Meets ANSI starting, end-of-life protection and sound rating specifications. Low THD.

6.Shielding: Tiger striped pattern pierced in extruded housing, regressed and backed by 0.20”(0.51cm) opal acrylic.

Electrical

Connections: Pre-wired with 18 gauge wires and polarized cannon plug connectors for simultaneous mechanical/electrical connection.

Emergency Battery Pack: 90 minute operation, 700 lumens for 54W and 520 lumens for 28W.

Dimming: Advance Mark X standard (no additional wires required); use compat- ible dimmer. Dimming ballasts using additional control wires (e.g. Lutron Hi-Lume or ECO-10, Osram) can be used; consult factory and use X4 or X5 power feeds with additional leads, as appropriate. Ballast not to exceed 1.25” (3.18cm) wide by 1.20” (3.05cm) high.

iGEN: F7000 accepts iGEN (DALI) with supplemental 2-wire control technology. Use with X5 power feed.

Power Tray: Code-gauge, die-formed steel, pre-paint white enamel finish; secured by quarter-turn fasteners for easy access to wiring. Holds ballasts, sock- ets, and wiring. Accepts ballasts up to 1.25” (3.18cm) wide by 1.20” (3.05cm) high.

Factory installed ballast disconnect allows the ballast to be disconnected from and reconnected to incoming power under load without turning the entire circuit off.

Finish

Powder-coated, baked enamel, white or aluminum, as specified.

Mounting

Each module includes two wall-mounting brackets. Bracket hole pattern accom- modates junction box (single gang box rotated 90 degrees) or other appropriate mounting method using customer supplied fasteners.

Labels

UL, cUL and I.B.E.W.

Ordering Instructions

Individual Fixtures:

1.Order one MODULE.

2.Order one END SET.

Continuous Rows:

1.Order the appropriate number of MODULES for the complete run.

2.Order one END SET.

Job Information Type:

Job Name:

Cat. No.:

Lamp(s):

Notes:


"JSQPSU
3PBE
'BMM
3JWFS
."

t


t
'BY

 We reserve the right to change details of design, materials and finish. XXXMJHIUPMJFSDPN
½

1IJMJQT
(SPVQ
t E0808