READ AND UNDERSTAND THESE INSTRUCTIONS

 

 

 

 

INSTRUCTION SHEET NO.

 

BEFORE INSTALLING LUMINAIRE.

 

 

 

 

 

 

IS:1000LVR

 

installation. To prevent electric shock, turn off electricity at main power supply before proceeding.

 

 

This luminaire is intended for installation in accordance with the National Electrical Code and local regulations.

 

 

 

 

 

To assure full compliance with local codes and regulations, check with your local electrical inspector before

 

 

 

 

 

Retain these instructions for maintenance reference.

 

 

 

 

 

 

 

 

 

 

 

B0607

 

Page 1 of 1

 

INSTALLATION PROCEDURE FOR: LYTECASTER® 1000LVR & 1000LVRE1 LOW VOLTAGE REMODELER KIT

CAUTION: USE ONLY WITH REFLECTOR TRIMS PROVIDED BY LIGHTOLIER. USE OF OTHER MANUFACTURER’S TRIMS MAY VOID THE

UNDERWRITERS LABORATORIES LISTING AND COULD CONSTITUTE A FIRE HAZARD.

CAUTION: BEFORE INSTALLING FRAME-IN KIT AND REFLECTOR TRIM, READ ALL MARKINGS ON FRAME-IN KIT AND REFLECTOR TO

DETERMINE LAMP WATTAGE AND TYPE APPLICABLE FOR YOUR INSTALLATION.

WARNING: (RISK OF FIRE) DO NOT INSTALL INSULATION WITHIN 3” OF FIXTURE SIDES OR WIRING COMPARTMENT, NOR ABOVE

FIXTURE IN SUCH A MANNER SO AS TO ENTRAP HEAT.

1.CUT OPENING (Fig. A)

Use aperture sticker provided as a template to cut a hole in the ceiling. Cut to outside edge of sticker.

*Lightolier also offers a hole cutter (HC-356) that can be purchased separately to assist with quick, clean trim installations. In this case, follow the hole cutting directions supplied with HC-356.

Figure A

2. WIRE IN & PUSH THRU

Figure B

Wire to SUPPLY LEADS. (For Cable, use built in CABLE CLAMP in J-BOX). WHITE FIXTURE LEAD to NEUTRAL SUPPLY LEAD. BLACK FIXTURE LEAD to

HOT SUPPLY LEAD (120V). BARE FIXTURE LEAD WIRE TO SUPPLY GROUND. Use wirenuts (local hardware item). Place all electrical connections in J-Box. Attach J-BOX cover onto J-BOX. For flexible CONDUIT, use 90° connector (not supplied) or 3/8” SPRING CONNECTOR (provided). If 3/8” SPRING CONNECTOR is used, place J-BOX and TRANSFORMER ASSEMBLY onto ceiling, attach CONNECTOR to CONDUIT and push into one of the 7/8” dia. knock out holes in J-BOX. Pull J-BOX and TRANSFORMER ASSEMBLY toward ceiling opening (as shown in Figure B) and complete wiring.

Figure C

3.ATTACH MOUNTING RING (Fig. D)

Push MOUNTING RING into opening until FLANGE sits against ceiling. Slide MOUNTING STRAPS down to trap ceiling thickness and then bend up to secure (Fig. E). Make sure “J-BOX” SLOT on REMODELER RING is in a position that will ensure enough space above ceiling for J-BOX to sit flat against ceiling.

Figure DFigure E

4. ATTACH J-BOX (Fig. F)

Insert J-BOX MOUNTING STRAP between the ceiling material and MOUNTING RING and through the “J-BOX” SLOT on the MOUNTING RING. Pull the STRAP until the J-BOX PLATE sits flat on the ceiling with the feet over the edge of the ceiling thickness (Fig G). Bend J-BOX PLATE MOUNTING STRAP up to secure. Make sure J-BOX PLATE is securely attached to the ceiling and the J-BOX is in the shown position.

Figure F

 

 

 

Figure G

 

 

 

 

 

 

 

 

 

 

 

 

5.

SNAP-ON (Fig.H)

SEE SEPARATE

 

 

 

REFLECTOR TRIM

 

 

 

INSTRUCTION

 

 

6.

PUSH-UP (Fig. I)

SHEETS

 

 

 

 

 

 

Figure H

 

 

Figure I

 

 

 

 

A

 

COMPANY

 

 

 

 

 

 

 

 

631 Airport Road, Fall River, MA 02720

Page 1
Image 1
Lightolier IS:1000LVR instruction sheet IS1000LVR, Wire in & Push Thru, See Separate Reflector Trim Instruction, Sheets

IS:1000LVR specifications

The Lightolier IS:1000LVR is a sophisticated lighting solution designed to meet the diverse demands of modern lighting applications. This exceptional offering from Lightolier integrates advanced technologies, versatility, and energy efficiency, making it an ideal choice for both residential and commercial spaces.

One of the main features of the IS:1000LVR is its ability to deliver superior lighting performance while maintaining energy efficiency. The fixture utilizes cutting-edge LED technology, which not only provides bright, clear illumination but also significantly reduces energy consumption compared to traditional lighting sources. This LED system has a long lifespan, often exceeding 50,000 hours, translating to lower maintenance costs and reduced frequency of replacements.

The IS:1000LVR is designed with versatility in mind. Its sleek, modern aesthetic allows it to seamlessly blend into various interior styles while providing effective task and ambient lighting. The adjustable head provides flexibility in directing light where it’s needed most, making it suitable for a range of settings from homes to offices. Whether for highlighting artwork or providing general illumination in a workspace, this fixture excels at adaptability.

Moreover, the IS:1000LVR incorporates advanced dimming capabilities, allowing users to customize the lighting levels according to their preferences and needs. This feature not only enhances comfort but also contributes to energy savings by enabling effective control over light output. The unit can be easily integrated with existing smart home systems, enhancing its functionality through remote operation and scheduling.

In terms of installation, the IS:1000LVR boasts a user-friendly design that simplifies the process for contractors and DIY enthusiasts alike. Its compact size ensures that it can fit into a variety of ceiling types, while the straightforward mounting options facilitate hassle-free setup.

The Lightolier IS:1000LVR stands out for its blend of technology, efficiency, and aesthetic appeal. It’s an excellent choice for anyone looking to enhance their lighting experience while also considering environmental impact and energy consumption. With its impressive features and reliable performance, the IS:1000LVR is poised to become a staple in innovative lighting design.