Lightolier IS:26060 instruction sheet Cut the Wire Cover to the desired length

READ AND UNDERSTAND ALL TRACK, CONNECTOR, FEED-IN-KITS, AND ACCESSORY

INSTRUCTION SHEETS BEFORE INSTALLING ANY PROSPEC® TRACK ITEM.

This fixture is intended for installation in accordance with the National Electrical Code and local or Federal code specifications. To assure full compliance with codes and regulations, check with your local electrical inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

INSTRUCTION SHEET NO.

IS:26060

0597 Page 2 of 2

FLOATING FEED MOUNTING INSTRUCTIONS (Flush 26060WH, BK and Standoff 26061WH, BK)

Mounting the CANOPY at some distance away from the end of the FEED TRACK or FEED CONNECTOR.

NOTE: Hardware is supplied to mount the CANOPY a maximum of 4 feet from the FEED CONNECTOR. DO NOT EXCEED THIS DISTANCE.

1.Mark CENTER LINE of TRACK through CENTER LINE of OUT-

LET BOX.

2.NOTE: The CANOPY mounts to a 3 or 4” OCTAGON OUTLET BOX. The MOUNTING HOLES of the OUTLET BOX should be at 45° to the longitudinal axis of the TRACK. (Fig. 1)

3.Break the BARRIER off the FEED CONNECTOR or FEED TRACK. (Fig. 6)

4.Remove the DEAD END from the TRACK and retain.

5.Assembly the “U” BRACKET onto the PLATE ASSEMBLY using the FLAT HEAD SCREW. (Fig. 6)

6.Run the feed wires along the top of the TRACK and into the FEED CONNECTOR or FEED TRACK. (2 HOTS, 2 NEUTRALS, AND GROUND; MAXIMUM)

PLATE

WIRE COVER ASSEMBLY FLAT HEAD SCREW

90°TAB

TRACK UNIT
		U BRACKET
FEED CONNECTOR	BARRIER	DEAD
		END

FIG. 6 FEED IN POINT

7.NOTE: USE 12 GA. COPPER THHN WIRE INCLUDING GROUND. IF STRANDED 12 GA WIRE IS USED THE ENDS MUST BE TINNED.

8.Cut the WIRE COVER to the desired length.

9.Slide the WIRE COVER (over the wires) and PLATE ASSEMBLY into the TRACK. NOTE THE POSITION OF THE 90° TAB IN RELATION TO THE FEED-IN POINT. Pass the wires through the center hole of the PLATE ASSEMBLY.

10.Secure the PLATE ASSEMBLY to the TRACK by tightening the

SCREW. THE WIRE COVER MUST COVER THE ENTIRE LENGTH OF WIRES ON TOPS OF THE TRACK.

11.Mount the TRACK to the ceiling (see instruction sheet 26000 provided with the track or IS:26478). Positioning the PLATE ASSEMBLY over the J-BOX.

12.Splice the wires from the track to the wires in the J-BOX.

BLACK TO BLACK, WHITE TO WHITE, AND GROUND TO GROUND.

13.Rotate the PLATE ASSEMBLY until the SLOTS are in-line with the MOUNTING HOLES on the J-BOX.

14.Secure the PLATE ASSEMBLY to the J-BOX using the THIN HEAD SCREWS. (Fig. 7)

15.Attach the GROUND WIRE on the CANOPY PLATE to the GROUND LEAD or GROUND TERMINAL in the J-BOX. (Fig. 7)

16.WHEN USING THE FLUSH CANOPY 26060WH/BK. Slide the CANOPY PLATE between the TRACK and CROSS BAR on the PLATE ASSEMBLY. For added security of CANOPY PLATE: Drill a hole in CANOPY PLATE and secure to ceiling with a screw.

17.WHEN USING THE STANDOFF CANOPY 26061WH/BK. Slide the CANOPY PLATE between the CROSS BAR and NUT on the PLATE ASSEMBLY. Rotate the NUT to secure the CANOPY PLATE against the ceiling. (Fig. 8)

18.NOTE: THE CROSSBAR MUST COVER THE SLOT IN THE CANOPY PLATE AFTER ASSEMBLY.

U BRACKET

J-BOX

CROSS BAR

CANOPY PLATE

PLATE

ASSEMBLY

WIRE COVER

THIN HEAD

SCREW

TRACK UNIT

POWER EXTENSION

CONNECTOR

FIG. 7

J BOX

CANOPY

PLATE

TRACK UNIT

NUT

19.	Follow the instructions for wiring on the instruction sheets	FIG. 8	POWER EXTENSION
	included with the the “FEED TRACK” or “CONNECTOR”.		CONNECTOR
20.	Assembly the DEAD END into the end of the TRACK.

®

LIGHTOLIER a GENLYTE company.

631 Airport Road, Fall River, MA 02720