INSTRUCTION SHEET FOR ASSEMBLY AND INSTALLATION

OF 9”,12”&16” PENDALYTE™ SERIES WITH STEM

Note: This instruction sheet covers several luminaire styles. Powerhead assembly, lamp type, and reflector style may vary slightly from that shown, although installation is the same.

NOTE: If custom length is required see below

1.Assemble STEM to BALL ALIGNER using SET SCREWS. SET SCREWS should align with small holes near end of stem. Pull wires through BALL ALIGNER leaving no less than 6” exposed. (Fig 1)

2.Strip back insulation on Black, White and Green wires 3/8” at both ends.

3.Attach MOUNT PLATE to STEM by aligning holes as shown and inserting PIN. Secure PIN with COTTER PIN.

4.Wire POWERHEAD ASSEMBLY using WIRE NUTS (local hardware item): black luminaire lead to hot (black) lead, white luminaire lead to neutral (white) lead. Attach luminaire ground wire(s) (green and/or bare) to green ground wire.

5.Attach POWERHEAD to MOUNT PLATE with 8-32 SCREWS

6.Install SWIVEL CROSSBAR onto outlet box using OUTLET BOX SCREWS.

7.Insert STEM with BALL ALIGNER through CANOPY prior to wiring.

8.Place BALL ALIGNER with STEM into CROSS BAR through side access hole. When seated the BALL ALIGNER KEYWAY will line up with tab on CROSSBAR. Push supply leads into outlet box.

9.Slide SAFETY STRAP into position and secure with screw.

10.Make electrical connections: black lead to hot (black) supply lead; white lead to neutral (white) supply lead. Green lead is ground wire and must be connected to grounding terminal or ground lead inside outlet box. Use WIRE NUTS (local hardware item). Note: Refer to POWERHEAD instruction sheet for detailed wiring information.

11.Place CANOPY over CROSSBAR lining up slots on CANOPY with RUBBER CAPS on CROSSBAR turning clockwise until it locks into place.

Instructions for shortening stem

ATTENTION: Cut end with smaller diameter holes only. (Fig.1)

CAUTION: Eye protection should always be worn when using hand and power tools during the assembly procedure outlined below.

1.Using pipe cutting tool, shorten STEM to appropriate length. Clean all burrs and sharp edges from cut end of Stem.

2.Position DRILL LOCATOR over cut end of STEM (Fig. 2). Gently tap down on DRILL LOCATOR until fully seated on end of STEM.

3.Position CENTER PUNCH into bottom SLOT in DRILL LOCATOR and mark a small dimple in STEM (Fig. 3).

4.Align 1/8" DRILL BIT (local hardware item) into bottom slot of DRILL LOCATOR so tip of DRILL BIT rests in dimple (Fig. 4).

5.Drill hole completely through STEM allowing DRILL LOCATOR to guide DRILL BIT. Do not force DRILL BIT. It is recommended to hold DRILL LOCATOR securely in a vise or other device prior to drilling hole.

SET SCREW

KEYWAY

SWIVEL

CROSSBAR

RUBBER

CAPS

CANOPY

COTTER PIN

POWERHEAD

ASSEMBLY

Fig 1

BALL ALIGNER

SAFETY

STRAP

W/SCREW

OUTLET

BOX

SCREW

STEM

8-32 SCREW

PIN

MOUNT PLATE

Page 1 Page 1
Page 1
Image 1
Lightolier IS:404S36 instruction sheet Instructions for shortening stem
Page 1 Page 1

IS:404S36 specifications

The Lightolier IS:404S36 is an innovative lighting fixture that brings together cutting-edge design and advanced technology to meet a variety of lighting needs. Ideal for commercial and residential settings, this product is versatile in its application and offers an array of features that make it an attractive choice for various lighting projects.

One of the standout features of the IS:404S36 is its energy efficiency. Utilizing advanced LED technology, this fixture offers significant reductions in energy consumption compared to traditional incandescent and fluorescent lighting options. With a long lifespan of up to 50,000 hours, the LED technology not only reduces energy costs but also decreases the frequency of replacements, offering a sustainable solution for lighting.

The IS:404S36 is designed with flexibility in mind. It is available in multiple color temperatures, ranging from warm white to cool daylight, allowing users to select the ideal ambiance for their space. Whether it’s creating a cozy atmosphere in a living room or providing bright, efficient lighting in a workspace, this fixture can easily adapt to any environment.

Another significant aspect of the IS:404S36 is its sleek and modern design. With options for different finishes, it can complement various interior styles, making it a practical choice for designers and homeowners alike. The minimalist aesthetic ensures that it can blend seamlessly into any decor without being intrusive.

The fixture is also equipped with advanced dimming capabilities. This feature enables users to adjust the brightness in their space, enhancing comfort and functionality. Dimming not only allows for personalized lighting environments but also contributes to energy savings by reducing power consumption when full brightness is not necessary.

Durability is another key characteristic of the Lightolier IS:404S36. Constructed with high-quality materials, it is resistant to wear and tear over time, making it a reliable choice for environments prone to heavy use.

In summary, the Lightolier IS:404S36 stands out in the lighting industry due to its energy efficiency, flexibility, modern design, dimming capabilities, and durability. Whether for home or business applications, this fixture provides a perfect blend of functionality and aesthetic appeal, making it a valuable investment for anyone in need of quality lighting solutions.
Top Page Image Contents