Lightolier IS:44224 IIS$44224, COVERI?LATE Mounting Procedure, Glass Diffuser Installation

[ . [~sTRLJcTloNsj+EETNoo				I								~OUTLZT	BOX	COb’ER
—.-. —	L—	. .	.					OCIAGONAL	OUTLET	BOX y
IIS:$44224,					,			o“								.
								.			I
	—-------...—							o
“io94	PAGE	2	OF	2			1				\
,_.	..——.	.—.—			BACKPLATE”
					ASSf MBLY			CfU/SWITCH	OUTLET	BOX -	\
					MOUNTING	1					\
					HOLCS			0							0
								.							.
								0							0
,, ,..					~AcKpuTE		, -.	. . . .		.	~—. ..— ..—	——-	.-.	—-	.	. ..
					AS LCUSLYr ---					~~lGUR~		Z<i

3.pcsition BACKpLATE AS S~BLY centered over OUTLET BOX. Use a leVel placed on top of fixture. Once fixture is level, use MOUNTING

HOLES as a template and mark drill locations (see figure 2) .

.4. Usin~ all MOUNTING HOLES in BACKPLATE ASSEMBLY, secure to wall using wood screws, toggle bolts, or alternate fasteners (not pro- vided) depending on wall material. Note: care must be taken to insure that OUTLET BOX is completely covered.

F.OR HORIZONTALLY MOUNTED RECTANGULAR GEM OR SWITCH OUTLET BOXES:

1.Make,wiring connections per instruction provided in’istep 211above.

2.PositIon BACKPLATE ASSEMBLY per instruction provided in’lstep 3’1.

3.Mount BACKPLATE ASSEMBLY per instruction provided inf’step 4“ above.. Note: where fixture is mounted vertically, gem or switch outlet box must be also installed vertically.

COVERI?LATE MOUNTING PROCEDURE:

1;. Remcve THREADED KNOBS that secure END COVERS to COVER PLATE. Re- mcve END COVERS and set aside with THREADED KNOBS.

2; Install COVER PLATE onto THREADED STUDS (pressing firmly to compress the GROUNDING CLIP) on BACKP’LATE ASSZMBLY. ~se_ extreme

!

care to not pinch wires between parts. (Note: when installing fix-

Iture horizontally, observe llTHIS EDGE UP” marking on COVERP-LATE

I to insure proper orientation). Secure COVER PLATE to BACKPLATE ASSEMBLY by threading CAPSCREWS anto MOUNTING STU9S(see figure 1)

3.Install recommen~ed lamps. Caution: maximum wattage marked on the f~xture must not be exceeded.

GLASS DIFFUSER INSTALLATION:

1.Position GLASS DIFFUSER as shown in figure 3, step 1.

2.Move GLASS DIFFUSER towards COVER PLATE until UPPER and LOWER TABS on GLASS DIFFUSER touch COVER PLATE (see figure 3, step 2) .

3.Gently slide GLASS DIFFUDER in a downward direction until UPPER TABS fullv en~aae into HOLDER BRACKETS (see fiqure 3, step 3) .

4.While sup~ort~n~ GLASS DIFFUSER, install END COVERS onto THREADED STUD on COVER PLATE. Secure END COVERS by installing THREADED KNOB onto THREADED STUD. Note: ENDCOVERS that are closed-off on

one side are used on either end of fixture to close-off the _ HOLDER BRACKETS on the very ends (see figure 3, step 3) ..

—		.	‘m–—-––-’-””	““” - —
o	/
			w	CD
1
i*\“f		LOWER	r--	HOLDER BRACKCT
		VII)		KNOB
7		.TABS		“/
/’
		/		ENO COVER
+$				—
				,—
				B<
				THREAOED.

I‘“- GLASS L<-

OIFFUSZR COVER PLATE

–FIGURE 3–