Lightolier LSB-5 manual Ordering Information, Features, Electrical, Mountings, Finish, Labels

		Lighting Systems LSB-5
1BHF  PG 	-ZUFTQSFBEÜ -4# 1JFSDFE -VNJOPVT *OEJSFDU -JHIU 5 1FS 'PPU /PNJOBM 4FDUJPO

8-1/2” (21.59cm)

1-3/4" (4.45cm)

3 1 2 4

3-1/2" (8.89cm)

Fixture Shown Half Scale

Pierce Pattern

Ordering Information

Family	Lamps
LSB	1
	1 = 1-Lamp T5

Complete ordering instructions below.

5/8" (1.59cm)

	Length	Shielding
		B
4	= 4-Foot	B = Pierced
8	= 8-Foot

3/16"
(0.48cm)			1/16"
3-1/16"			(0.16cm)
(7.78cm)
		Ballast		Voltage	Finish
28		= 28W T5		1 = 120 volt	AL = Aluminum
54		= 54W T5		2 = 277 volt	WH = White
	5E	= 54W T5 Emergency Pack
	2E	= 28W T5 Emergency Pack
	5D	= 54W T5 Dimming

Features

1.Housing: Extruded aluminum. Die-cast end cap mechanically attached with no exposed fasteners or hardware.

2.Lamping: One T5, 28 or 54 watt (as specified) fluorescent lamp per 4-Foot nominal section. Provided by others.

3.Reflector: Precision die-formed semi-specular aluminum.

4.Shielding: Precision die-formed, pierced 20 gauge CRS. Piercing is four rows that extend the entire length of the lamps. The pattern is 5/8” (1.59cm) x 1/16” (0.16cm) slot with a 3/16” (0.48cm) separation between rows.

Electrical

Ballast is <10% THD, .98 ballast factor, pre-heat start. 18 gauge wire. Color- coded quick connectors allow ease of connection for joiner modules. Power feed is 18 gauge white SJT. For special circuiting consult factory. Factory installed ballast disconnect allows the ballast to be disconnected from and reconnected to incoming power under load without turning the entire circuit off.

Dimming: 120/277 VAC 1% dimming level, 4 wire feed required.

Emergency Battery Pack: 28 watt: 520 lumens @ 90 minutes, 54 watt: 700 lumens @ 90 minutes, 4 wire feed required.

Mountings

Cable suspension (not shown) - 4-1/2" (11.43cm) diameter canopy finished white enamel, 1/16" (0.16cm) diameter stainless steel aircraft cable adjustable up to 36" (91.44cm). Dual-screw draw-tight connector to create hairline seam between joiner modules.

Finish

Powder coated baked white or aluminum finish. Custom colors available, consult factory.

Options and Accessories

Emergency Circuiting; special circuiting; X, T & L joiner blocks - consult factory.

Labels

UL, cUL and I.B.E.W.

Ordering Instructions

Individual Fixtures:

1.Order number of MODULES required.

2.Order one POWER FEED END SET per MODULE.

Continuous Rows:

1.Determine run length.

2.Order the appropriate number of MODULES for the complete run.

3.Order one POWER FEED END SET per run.

4.Order one CABLE ASSEMBLY per MODULE minus one per run.

5.For runs that exceed amperage limits, order the appropriate number of

CABLE/CORD ASSEMBLIES.

Job Information Type:

Job Name:

Cat. No.:

Lamp(s):

Notes:


"JSQPSU
3PBE
'BMM
3JWFS
."

t


t
'BY



We reserve the right to change details of design, materials and finish.

XXXMJHIUPMJFSDPN
½

1IJMJQT
(SPVQ
t #