1 Gear Box Assembly
See P-100-C
1XXXX
2 Face Plate L6987 1 X X X X
3* Idle Roll Assembly S12475 1 X X X X
4* Incoming Guide Tube (3/32 thru 7/32”) KP2116-2 1 X • • •
4* Incoming Guide Tube (1/16 thru 3/32”) KP2116-1 1 • X • •
4*
Incoming Guide Tube [.035 thru .052” (.045 thru .052” Cored)]
KP1967-1 1 • • X X
5
5/16-18 x .75
HHCS
CF000040
2XXXX
6 Mounting Clip T8400 4 X X X X
7
3/16-16 x 3.00
HHCS
CF000039
1XXXX
8 Plain Washer S9262-120 1 X X X X
9 Pivot Pin T12206-1 1 X X X X
10 Idle Roll Spring T10247-7 1 X X X X
11 Yoke Indicator Assembly T13610 1 X X X X
12 Drive Roll Nut T10552 1 X X X X
13 Drive Roll Washer S9262-44 1 X X X X
14* Drive Roll (3/32” thru 7/32”) S12514 2 X • • •
14* Drive Roll (1/16” thru 3/32”) S12515 2 • X • •
14* Drive Roll (.035” thru .052”) S12778 1 • • X •
14* Drive Roll (.045” thru .052” Cored Wire)(NA5,NA4,NA3) S19113 2 • • • X
16 Snap Ring S11910-2 1 X X X X
17 Drive Roll Key M8776-5 1 X X X X
18 Wire Straightener, Single Wire
See P-100-K or -M
1XX••
19* Outgoing Tube (3/32” thru 7/32”) S10170-1 1 X • • •
19* Outgoing Tube (1/16 thru 3/32”) T13635-3/32 1 • X • •
19*
Outgoing Tube [.035 thru .052” (.045 thru .052” Cored)]
T13635-.052 1 • • X X
20 Socket Head Cap Screw T9447-12 2 X X X X
21 Socket Head Cap Screw T9447-32 1 X X X X
24 24 Thru 27 See P-100-F X X X X
28 Cross Seam Adjuster Assembly See P-100-L 1 X X X X
29 29 thru 34 See P-100-F X X X X
35 Plain Washer S9262-131 1 X X X X
36 Locking Key T14896 1 X X X X
37 Hollow Head Set Screw S11604-8 1 X X X X
Optional Drive Roller Conversion Kits:
(Includes Drive Roll, Incoming & Outgoing Guide Tubes)
3/32” thru 7/32” Wire T13724-A
1/16” thru 3/32” Wire T13724-B
.035” thru .052” Solid Wire T13724-C
.045” thru .052” Cored Wire T13724-D
.035” thru .045 Spring Guide T9367-4
09-27-2007
P-100-D.3P-100-D.3
Sub Assembly Illustration Sub Assembly Illustration Sub Assembly Illustration Sub Assembly Illustration
For 3/32 thru 7/32” wire, use the parts marked “X” in column 1.
For 1/16 thru 3/32” wire, use the parts marked “X” in column 2.
For .035 thru .052” wire, use the parts marked “X” in column 3.
For .045 thru .052” Cored Wire, use the parts marked “X” in column 4.
ITEM DESCRIPTION PART NO. QTY. 1234567 89
* For Twinarc (two electrodes fed through one head)
parts, see the appropriate Twinarc Assembly parts
list in the P-101 series.
# Indicates a Change This Printing
Note: When using K231 or K233 Contact Nozzle, a
long guide sleeve is required inside the nozzle.
See P-202-M or P-101-D.