
®
Installation Instructions
GARAGE DOOR
RADIO CONTROLS
MODEL 1099-31 RECEIVER
WARNING:
•Disconnect power before any installation or repair.
•Wear safety glasses.
Your
SELECTING A CODE
The code is determined by the positions of the 10 small switches numbered 1 through 10 located on the receiver board. To gain access to the switch, remove the top section of the case. Any combination of ON (CLOSED) or OFF (OPEN) positions can be selected by using a small screwdriver or ball point pen (see figure 1). We strongly urge that you avoid the following code schemes: ALL ON, ALL OFF, 2, 4, 6, 8, 10, ON or 1, 3, 5, 7, 9, ON. These codes are frequently used by other manu- facturers, and create the possibility of false opera- tion, and may be less secure than other code schemes.
Begin your installation of the 1099 by correctly wiring the receiver to the devices you will be using. WE URGE YOU TO BECOME FA-
MILIAR WITH THE INSTRUCTIONS THAT THE MANUFACTURER OF YOUR EQUIPMENT HAS PROVIDED. SINCE, I N MANY CASES, THESE INSTRUCTIONS WILL DETERMINE THE WAY IN WHICH THE 1099 RECEIVER W I L L B E I N-
STALLED.
The receiver should be mounted near the opener power head and can be installed in any position by using screws and the two slots in the cover flanges. Select a location and position that permits access to the terminals and space for the antenna as clear of metal structures as possible and preferably in a vertical position.
Wire the red and black wires to a 24VAC/DC power supply. Connect the remaining gray wires as specified by the manufacturer of your operator. If such instructions do not exist, wire the two gray wires in parallel with the pushbutton termi- nals. If the operator has a three wire terminal, the proper terminals will usually be marked “1” and “2” or “24V” and “RELAY” (see figure 2).
At this point you should mount your 1099 receiver to its permanent installation, if you have not already done so.
RED | 1 |
| |
GRAY | CONTROL | ||
| |||
GRAY | 2 | ||
BOX | |||
|
|
ADDITIONAL INSTALLATION INFORMATION
Linear Corporation has taken every possible precaution to make the 1099 receiver as reliable as possible. We think the following notes should be observed:
1.Be sure the unit is sealed from moisture, and, if at all possible, keep it away from direct moisture.
2.In those installations where vibration may be a factor, be sure to use a fastening compound, such as LOCTITE (TM) on the mounting screws to insure reliable mounting.
3.If this, or any other equipment is being used in a
OPERATIONAL CHECK
To check operation, move back a reasonable distance (about 50 feet) and press the transmitter button. Operation should be reliable at this distance but environment and location of both the transmitter and receiver will affect the range. If the transmitter is stowed well out of sight, it may be necessary to remove it from its mounting and hold near the windshield. Try different locations and positions. If operation is still unsatisfactory, check the following:
1. | The antenna must be connected to the receiver for |
| normal use. |
2. If the opener fails to operate, check to see that 115 VAC | |
| power is present. Check circuit breakers or for a system |
| power failure. |
3. | If the opener operates by pressing the wall button, but |
WARRANTY
All
CAUTION: Any changes or modification in intentional or unintentional radiators which are not expressly approved by LINEAR CORPORATION could void the user’s authority to operate this equipment.
LINEAR CORPORATION
2055 Corte del Nogal • Carlsbad, CA 92009
(760)
Be certain to check that the code is functional before completing the installation.
CODE SWITCH
Figure 1
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 |
OPEN
BLACK
RECEIVER
ANTENNA INSTALLATION
3
Figure 2
(1099-31)
not when the transmitter button is pressed, the radio |
controls are probably at fault. Check to make sure |
both transmitter and receiver code switches are set |
to the exact same code since a difference of just one |
switch will prevent operation. Check transmitter bat- |
tery, location of the transmitter and receiver installation. |
4. Try mounting the antenna at a more favorable remote |
location by utilizing the coaxial kit. |
If, after performing the above operational check, it is necessary to return the radio controls, return
INSTALLATION
The receiver comes equipped with an
After you have mounted your receiver, test it with the enclosed antenna for range, noting the coverage that you get from all desired operating loca- tions. If greater range or coverage pattern is necessary, you may need the 1066 Coaxial Wiring Kit, which is available from your dealer. It is not advisable to add lengths of coaxial cable greater than 20 feet, as this may affect range or tuning.
both the transmitter and receiver to your dealer for repair or replacement or they may be returned, postage prepaid, directly to Linear Corporation.