Encore | 1. | PRODUCT DESCRIPTION | 2. EMITTER DETAILS |
|
| |||||
The Model |
|
|
|
|
| |||||
Distribution System |
| Model | Side View | |||||||
a package of four and are used with the Linear Encore |
| |||||||||
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| |
|
|
| Audio Distribution System, |
|
| NOTE: White side | 1/4" | |||
|
|
| 3.5 mm mono |
| ||||||
|
| local input wall plates. These generic emitters can also be used | (+) | stripe is positive (+) |
| |||||
|
| mini plug |
| |||||||
|
|
|
|
| Top View | |||||
|
| with Linear’s video hubs, 2100A and 2010 |
|
|
|
| ||||
|
|
|
|
|
| 5/16" | ||||
|
|
| a 5500 series IR enabled modulator connected to a video hub. |
|
|
|
|
| ||
|
| Each emitter contains a tiny infrared LED housed in a miniature, |
|
|
|
| ||||
IR Emitter |
|
|
|
| 7 FT | 3 FT | 9/16" | |||
|
| injection molded plastic shell. The emitters have adhesive backing |
|
|
| The emitter's shell, though dark in | ||||
|
|
| for mounting. An emitter can be installed directly on the IR sensor |
| Internal |
| ||||
|
|
|
|
|
|
|
|
|
| |
|
|
|
| window of the controlled source component or in a suitable nearby |
| IR Emitter |
| appearance, is transparent to | ||
Installation |
|
| High | Low | ||||||
|
| location. | handheld remote controls will pass | |||||||
|
|
|
|
|
|
|
|
| infrared light. Commands from | |
Instructions |
| An IR emitter repeats IR remote control signals received at a room | Output | Output | through the emitter case to the | |||||
| Side | Side | ||||||||
| source component. |
| ||||||||
| station keypad or IR target from a handheld IR remote control. |
|
|
|
| |||||
|
|
|
|
|
|
|
|
| ||
|
|
|
| When an IR signal is detected at a target, the signal is sent to the |
| Emitter | Clear adhesive layer |
| ||
|
|
|
| IR OUT jacks on the wall plates or device. An IR emitter connected |
|
| ||||
|
|
|
|
| (Replace, if necessary, |
| ||||
|
|
|
|
| Shell |
| ||||
|
|
|
| to the IR OUT jack, repeats the same IR signal to the source |
| with a short piece of |
| |||
| USA & Canada (800) |
|
|
| ||||||
|
|
|
| |||||||
| component. This allows IR remote control of source components |
|
|
| ||||||
| (760) |
|
|
| ||||||
|
| www.linearcorp.com | that are located away from the IR target. |
| Lead |
|
|
| ||
3. ATTACHING EMITTER TO COMPONENT | 4. | CONNECTING EMITTER TO SOURCE |
| LIMITED WARRANTY |
| |||||
IR Sensor | IR Controlled Components |
|
| This Linear product is warranted against defects in material and workmanship for twenty | ||||||
Window |
|
| Cabinet Door |
|
| four (24) months. This warranty extends only to wholesale customers who buy direct | ||||
|
|
|
|
| from Linear or through Linear’s normal distribution channels. Linear does not warrant | |||||
|
|
|
|
|
| |||||
|
|
|
|
|
| this product to consumers. Consumers should inquire from their selling dealer as to | ||||
|
|
|
|
| Connect IR emitter to source | the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the | ||||
|
|
|
|
| part of Linear LLC for consequential damages arising out of or in connection with | |||||
|
|
|
|
| input wall plate IR OUT jack | use or performance of this product or other indirect damages with respect to loss | ||||
Emitter attached directly |
| Emitter attached to |
| or to the IR OUT jack provided | of property, revenue, or profit, or cost of removal, installation, or reinstallation. All | |||||
to IR sensor window | Shelves | front cabinet door directly |
| on other sources | implied warranties, including implied warranties for merchantability and implied warranties | |||||
|
|
| opposite IR sensor window |
|
| for fi tness, are valid only until the warranty expires. This Linear LLC Warranty is in lieu | ||||
|
|
|
|
|
| |||||
> Peel off the adhesive cover and affix the emitter to the center of the IR sensor |
|
| of all other warranties express or implied. |
|
| |||||
window on the controlled component's front panel |
|
| All products returned for warranty service require a Return Product Authorization Number | |||||||
|
|
|
|
|
| |||||
> In some cases, it may be difficult to find the location of the IR sensor on the |
|
| (RPA#). Contact Linear Technical Service at | |||||||
component. Consult the owner's manual of the unit for the IR sensor location. |
|
| important details. |
|
|
| ||||
|
| Shelves |
|
| To IR emitter |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| |
| Sensor attached on shelf directly |
| Source Input |
|
|
|
|
| ||
|
| Wall Plate | Copyright © 2009 Linear LLC |
|
| P691 | ||||
| above or below IR sensor window |
|
|
| ||||||
|
|
|
|
|