Linear DXS-62/EC, DXS-63/EC manual

DXS-62/EC

DXS-63/EC BY

SUPERVISED

EMERGENCY

TRANSMITTERS

Operation Instructions

(760)438-7000 • FAX (760) 438-7043 www.linearcorp.com

WRISTBAND INSTALLATION

TO INSTALL WRISTBAND, SLIDE STRAPS

INTO SLOTS ON ENDS OF TRANSMITTER

NOTE: THE END OF STRAP WITH VELCRO ATTACHES TO THE END CLOSEST TO THE SIGNAL INDICATOR

STATUS OPTION & PROGRAMMING

IF THE FOUR HOUR STATUS TIMER IS REQUIRED FOR SUPERVISION, PERMANENTLY ENABLE THE TIMER BY PRESSING THE TRANSMITTER BUTTON FIVE TIMES IN SUCCESSION (USE THE LEFT BUTTON ON DXS-63). THE DXS-62

WILL BEEP AFTER EACH BUTTON PRESS, THE DXS-63 WILL NOT. FIVE BEEPS WILL SOUND WHEN THE TIMER IS ENABLED.

		...
	BEEP ...
...		BEEP
BEEP ...		BEEP
BEEP

PROGRAM THE TRANSMITTER INTO THE RECEIVER BY PLACING THE RECEIVER INTO PROGRAM MODE, THEN SEND A SIGNAL TO THE RECEIVER FROM THE TRANSMITTER. REFER TO THE RECEIVER'S PROGRAMMING INSTRUCTIONS FOR DETAILS.

PRODUCT DESCRIPTION

The Models DXS-62 and DXS-63 are battery powered, miniature, water-resistant*, supervised transmitters designed for use in emergency applications with Linear’s DX and DXS Format receivers. Each is supplied with a wristband, a pocket clip, and a Nylon pendant necklace. Pressing buttons on either transmitter sends a digital coded wireless signal to its companion receiver. To insure sending a complete signal, press the transmitter button(s) for a minimum of two seconds.

Each DXS transmitter is factory set to a unique code, so no ﬁ eld coding is required. The one-button DXS-62 sends a signal when its button is pressed. The two-button DXS-63 transmitter sends a signal when both buttons are pressed together. These transmitters can send a signal for up to 30seconds per activation. The red signal indicator on the transmitter lights and a built-in sounder beeps when the unit is activated.

If status transmissions are enabled, they will be sent every two hours. Some receivers are able to use these signals, others are not.

Every two hours the transmitter tests for a low battery. This test takes place even if status transmissions have not been enabled. If the battery tests low, the transmitter sounder will beep and a low battery signal will be sent.

Receivers must be programmed to the transmitter’s code before system testing and operation. Refer to the receiver’s instructions for details on operation and programming.

Each transmitter is sealed to provide water-resistance. The unit’s battery is not replaceable. The transmitter should be discarded at the end of its battery life.

* NOTE: Water resistance not tested by UL

PENDANT HOLDER INSTALLATION

TO INSTALL PENDANT HOLDER, SLIDE HOLDER INTO SLOTS ON ENDS OF TRANSMITTER

NOTE: NECKLACE SIDE OF PENDANT HOLDER FITS CLOSEST TO THE SIGNAL INDICATOR

SYSTEM TESTING

IMPORTANT! TEST SYSTEM WEEKLY

The manufacturer strongly recommends that you test security equipment frequently. Over a period of time, no electronic products are better than the inspection and maintenence they receive. Therefore, from the time of installation, it is absolutely necessary to test the system at least once a week.

PLACE THE RECEIVER IN A "TEST"

MODE AND ACTIVATE THE

TRANSMITTTER. VERIFY THAT THE

SIGNAL IS RECEIVED AND THAT THE

SYSTEM REPORTS AS REQUIRED.

...

BEEP

FEATURES

ACTIVATION

BUTTON

SIGNAL

INDICATOR

		ACTIVATION
	DXS-62	BUTTONS
	DXS-62	(PRESS BOTH)
		(PRESS BOTH)
		DXS-63
		NYLON
		NECKLACE

POCKET	WRIST
CLIP	STRAP

PENDANT HOLDER

POCKET CLIP INSTALLATION

INSTALL THE PENDANT HOLDER

THEN CUT AND REMOVE THE NECKLACE

SNAP THE POCKET CLIP

INTO THE PENDANT HOLDER

INTERNATIONAL WARRANTY

This Linear product is warranted against defects in material and workmanship for twelve (12) months. The Warranty Expiration Date is labeled on the product. This warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of Linear Corporation for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or proﬁt, or cost of removal, installation, or reinstallation. All implied warranties, including implied warranties for merchantability and implied warranties for ﬁ tness, are valid only until Warranty Expiration Date as labeled on the product.

This Linear Corporation Warranty is in lieu of all other warranties express or implied. For warranty service on Linear equipment return product, at sender’s expense to: Linear Hong Kong 19/F Hounor Industrial Centre, 6 Sun Yip Street Chai Wan, Hong Kong Attention: Repairs Department

REPAIRS POLICY

Charges will be made for equipment that is not in warranty, shows customer abuse, or is damaged by the effects of lightning, water, ﬁ re, or other abnormal happenings.

Customer’s equipment sent in for repair may be repaired or replaced with new or remanufactured equipment at Linear’s discretion.

The customer is always responsible for shipping and handling charges to the repairs facility. Linear will pay return shipping and handling charges on “in warranty” products shipped back

to the customer. The customer will be billed for the return shipping and handling charges on “out of warranty” products.

There will be a 50% expedite fee for any express requests.

The International Sales Manager must be notiﬁ ed prior to the return of product to Linear. All international returns must have an International Repair Authorization number (IRA#). The number

must be marked on all packages. Failure to do so will cause delays in processing.

IMPORTANT !!!

Linear radio controls provide a reliable communications link and ﬁ ll an important need in portable wireless signaling. However, there are some limitations which must be observed.

The radios are required to comply with local rules and regulations as radio devices. As such, they have limited transmitter power and therefore limited range.

A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings.

Changes or modiﬁ cations to the device may void regulatory compliance.

Infrequently used radio links should be tested regularly to protect against undetected interference or fault.

A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users.

215558 D