Linear ET-2 warranty Code Setting, Product Description Features

OFFON

ET-2

MINIATURE

PENDANT

TRANSMITTER

Code Setting

Instructions

USA & Canada (800) 421-1587 & (800) 392-0123

(760)438-7000 - Toll Free FAX (800) 468-1340 www.linearcorp.com

CODE SETTING

When Linear’s digital security radios leave the factory, the are set to a predetermined factory test code. In order to avoid duplicating codes in adjacent systems, the factory-set codes should not be used. Among the 256 possible codes, four other codes should not be used: all keys set to ON, all keys set to OFF, and keys set in in alternating ON/OFF or OFF/ON positions.

The digital coding switch in the ET-2 is located under the battery cover of the unit. To access the switch, remove the battery cover by twisting the lanyard loops apart. Note that the coding switch

has eight keys numbered 1 through 8. Use a paper clip or any other pointed object (except a pencil or pen) to

						8
set the keys ON or OFF to the code you select.						7
Make sure the keys are set all the way on or						6
off by pushing against them firmly.						5
In	the	example shown, keys			4	8
numbered 1, 4, 6, and 8 are set
				3
to ON: the keys numbered
				2
2,	3, 5,	and 7 are OFF.
Replace the battery access			1

cover.

1

PRODUCT DESCRIPTION	FEATURES
The Model ET-2 is a digitally coded miniature radio transmitter. This transmitter
can be programmed to activate any of Linear’s standard digital receivers that are
tuned to the same frequency. The ET-2 can perform many remote switching tasks		SNAP
and is typically used in wireless/hardware security systems. The ET-2 is powered		CORD
		RELEASE
by a self-contained 12-volt battery and includes a battery test/operation LED.
Measuring only 1.5 by .75 inches, the ET-1B can be worn on the supplied lanyard	NYLON
or attached to a keyring.	NECK
	CORD
WARNING: The button must be pressed for a minimum of two seconds to
cause receiver activation.
		CORD
		LENGTH
	ACTIVATION	ADJUSTMENT
	BUTTON
	SIGNAL
	INDICATOR

CHECKOUT AND TEST	LINEAR LIMITED WARRANTY
After setting the appropriate code in the ET-2 transmitter and its companion	This Linear product is warranted against defects in material and workmanship for twelve (12) months. This
receiver, the transmitter and receiver should be tested as a system. The receiver	warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal
	distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from
should be powered as described in the Code Setting and Installation Instructions
	their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities
enclosed with the receiver.	on the part of Linear LLC for consequential damages arising out of or in connection with use or
To test the ET-2 Transmitter, perform each of the following steps:	performance of this product or other indirect damages with respect to loss of property, revenue,
	or profit, or cost of removal, installation, or reinstallation. All implied warranties, including implied
STEP 1: Move at least six feet away from the receiver and activate the transmitter
	warranties for merchantability and implied warranties for fitness, are valid only until the warranty expires.
by pressing the pushbutton. The flashing red LED on the transmitter indicates that	This Linear LLC Warranty is in lieu of all other warranties express or implied.
the battery is good and a transmission is occurring. Receiver activation indicates	All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact
that the transmitter’s digital code is correctly matched to the receiver.	Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.
	IMPORTANT !!!
STEP 2: Operate the transmitter from various locations within the area to be
protected. This will help to locate possible null areas where structural metal and/	Linear radio controls provide a reliable communications link and fill an important need in portable wireless
	signaling. However, there are some limitations which must be observed.
or certain obstacles may interfere with transmission.
	 For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as
	Part 15 devices. As such, they have limited transmitter power and therefore limited range.
	 A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio
	signals that occur on or near their operating frequencies, regardless of code settings.
	 Changes or modifications to the device may void FCC compliance.
	 Infrequently used radio links should be tested regularly to protect against undetected interference or
	fault.
	 A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale
	distributor or dealer, and these facts should be communicated to the ultimate users.
	This device complies with FCC Part 15 and Canada Rules and Regulations. Operation is subject to the
	following two conditions: (1) This device may not cause harmful interference and (2) this device must
	accept any interference received, including interference that may cause undesired operation.
	Copyright © 2009 Linear LLC	229537B