Linear SXR-64A installation instructions Supervised Wireless Receiver, and Zone Expander

SXR-64A

INTRODUCTION

FEATURES

The

Model SXR-64A

is

a

64-channel,

12-zone, supervised wireless receiver/

✶ 64 Programmable Transmitter Channels

annunciator designed for use in residential or commercial security systems. Housed

✶ 8 Alarm Zones

in a rugged metal enclosure, the SXR-64A connects to a hardwired alarm control

Supervised Wireless Receiver

panel adding wireless capability to the panel.

✶ 4 Supervisory Zones

The SXR-64A receives signals from a variety of security transmitters then processes,

and Zone Expander

displays and transfers the signal to the hardwired alarm control panel. Six unique

✶ Rugged Metal Enclosure

conditions for each transmitter channel can be shown on the unit’s display. Conditions

✶ Six Condition Displays for Each Transmitter

such as “Open Portal”, “Transmitter Low Battery”, “Transmitter Tamper” and “First

✶ Alarm Memory with First-Alarm-In

Alarm In” show the status of each transmitter in the system. Valuable features such

as Alarm Memory and Transmitter Status allow for quick system diagnosis and

✶ Automatic Supervised Operation

troubleshooting.

✶ Transmitter Contact State Monitoring

The receiver’s eight alarm zones and four supervisory zones provide a fl exible

interface to the alarm control panel. Any or all of the zones can be used. All of the

✶ Transmitter Tamper Monitoring

solid state zone outputs can be either normally open or normally closed electrical

✶ Transmitter Low Battery Monitoring

confi guration and can switch up to 100 mA @ 24 VDC.

An easy programming interface using four pushbuttons lets the installer quickly setup

✶ Transmitter Status Report Monitoring

the system. The UP, DOWN, ADVANCE and MEMORY buttons are located inside the

✶ Easy Installer Programming Interface

receiver case and are used for transmitter and system programming.

An on-board, high-gain, superheterodyne radio receiver gives the SXR-64A excellent

✶ High-gain Superheterodyne Receiver

reception. The MODE indicator shows RF activity. The local whip antenna (supplied)

✶ Receiver Automatic Gain Control

or remote external antenna (Model EXA-1000) connects to the receiver through a

Installation Instructions

standard type “F” connector.

✶ Antenna Connector

The SXR-64A decodes Linear’s SX, S1, and MegaCode™ format transmitters. The

✶ Decodes 303.875 MHz SX, S1, & MegaCode™ Format Transmitters

SXR-64A can be used as a direct replacement for Linear’s SS-32, SSR-32, & SXR-64

receivers with an installation bonus of being able to use up to 64 transmitters in the

✶ Optional Display Blanking while Armed

system.

✶ RF Activity Indicator

Power for the SXR-64A is provided from the alarm control panel. To control the alarm

(760) 438-7000 • FAX (760) 438-7043

memory, reset tamper and status alert conditions, an armed input on the receiver

✶ Positive or Negative Armed Input

USA & Canada (800) 421-1587 & (800) 392-0123

connects to an armed output from the control panel.

Toll Free FAX (800) 468-1340

www.linearcorp.com

SYSTEM OVERVIEW

CONDITION DISPLAYS

COMPONENT LOCATIONS

TYPICAL TRANSMITTERS

CONDITIONS FOR ALL TRANSMITTERS

TX-91

TX-92

TX-94

T-90D

TMD-90

TSD-90A

ROTATE ON THE DISPLAY

ANTENNA CONNECTOR

TRANSMITTER DISPLAY

SHOWS THE TRANSMITTER'S

TYPE "F" ANTENNA CONNECTOR FOR

OPEN PORTAL

CHANNEL NUMBER AND IS USED

CONNECTION TO LOCAL OR REMOTE

DURING PROGRAMMING

ALL TRANSMITTERS WILL CAUSE THIS CONDITION WHEN AN ALARM SIGNAL IS

ANTENNA THROUGH RG-59 COAX

CONDITION DISPLAY

SENT. THE CONDITION WILL REMAIN UNTIL A RESTORE SIGNAL IS SENT, UNLESS

MODE LIGHT

SHOWS THE TRANSMITTER'S

THE TRANSMITTER IS SET AS "AUTO RESTORE". THE CHANNEL'S ZONE OUTPUT

LIGHTS WHEN UNIT IS

CONDITION AND IS USED DURING

PROGRAMMING

IN PROGRAM MODE,

WILL BE FAULTED WHEN THIS CONDITION IS DISPLAYED.

FLASHES WHEN RF IS

FIRST ALARM IN

RECEIVED IN RUN

MODE

WHEN THE PANEL IS ARMED, THE FIRST ALARM SIGNAL SENT WILL CAUSE THIS

CONDITION. IF THE CHANNEL IS SET AS "DELAYED", THIS CONDITION WILL OCCUR

ST-23A

LMT-1/303

MPX/303

AFTER ANY DELAYS IF THE PANEL IS NOT DISARMED. DISPLAY WILL CLEAR THE

NEXT TIME THE PANEL IS RE-ARMED.

MEMORY LIGHT

ADDITIONAL ALARMS IN

LIGHTS DURING PROGRAM

MODE TO SHOW WHEN A

WHEN THE PANEL IS ARMED, ADDITIONAL ALARM SIGNALS SENT WILL CAUSE THIS

TRANSMITTER HAS BEEN

CONDITION. IF THE CHANNEL IS SET AS "DELAYED", THIS CONDITION WILL OCCUR

ENTERED OR AN OPTION

HAS BEEN SELECTED,

AFTER ANY DELAYS IF THE PANEL IS NOT DISARMED. DISPLAY WILL CLEAR THE

TEST POINTS

LIGHTS DURING RUN MODE

UP TO 64 TRANSMITTERS

NEXT TIME THE PANEL IS RE-ARMED.

AUDIO TEST

WHEN SYSTEM IS ARMED,

POINTS FOR

BLINKS DURING EXIT DELAY

CAN BE USED

TRANSMITTER LOW BATTERY

LISTENING TO

RADIO INPUT

MEMORY BUTTON

ANY TRANSMITTER THAT CAN SEND A LOW BATTERY SIGNAL WILL CAUSE THIS

WITH BUTTSET

USED DURING PROGRAMMING

CONDITION WHEN ITS BATTERY IS LOW. DISPLAY WILL REMAIN UNTIL A SIGNAL

TO SELECT OPTIONS AND

FROM THE SAME TRANSMITTER WITH A GOOD BATTERY IS SENT.

ENTER TRANSMITTERS

TRANSMITTER TAMPER

ANY TRANSMITTER THAT CAN SEND A TAMPER SIGNAL WILL CAUSE THIS

CONDITION WHEN IT IS TAMPERED. DISPLAY WILL CLEAR THE NEXT TIME THE

UP & DOWN BUTTONS

PANEL IS ARMED.

PRESS EITHER TO ENTER

PROGRAM MODE, UP

TRANSMITTER STATUS ALERT

INCREASES AND DOWN

TERMINAL BLOCK

DECREASES VALUE DISPLAYED

CONNECTIONS FOR ZONE AND

PRESS TOGETHER TO EXIT

IF THE RECEIVER DOES NOT RECEIVE STATUS SIGNALS FROM A TRANSMITTER

PROGRAM MODE

SUPERVISORY OUTPUTS,

THAT IS SET AS SUPERVISED, THIS CONDITION WILL BE DISPLAYED. THE RECEIVER

POWER AND ARMED INPUTS

ADVANCE BUTTON

SXR-64A RECEIVER

ALARM CONTROL PANEL

CAN BE SET FOR TWO OR EIGHT HOURS OF MISSING STATUS TRANSMISSIONS

WIRING KNOCKOUTS

USED DURING PROGRAMMING

BEFORE THE CONDITION OCCURS. DISPLAY WILL CLEAR THE NEXT TIME THE

TO CHANGE ZONE NUMBERS

FOR WIRING CONDUIT

PANEL IS ARMED.

AND SELECT FUNCTIONS

CONNECTION

INSTALLATION TIPS

MOUNTING UNIT

ANTENNA INSTALLATION

90% - 100%

65% - 95%

10% - 70%

OF FULL POWER

OF FULL POWER

OF FULL POWER

USE SCREWS AND ANCHORS TO

7"

MOUNT THE RECEIVER

CONSTRUCTION

MATERIALS WILL

EFFECT RADIO RANGE

MOUNTING

5"

5"

WALLBOARD AND

LIGHT CONCRETE

CONCRETE WITH STEEL

PATTERN

WOOD STUDS

OR BRICK

REINFORCEMENT OR

USE LOCAL

METAL LATH AND PLASTER

WHIP ANTENNA

(SUPPLIED)

RECEIVER (ANTENNA)

- OR -

LOCATION EFFECTS

RCVR

RADIO RANGE

RCVR

BASEMENT

BASEMENT

USE THE

MODEL EXA-1000

RIGHT

WRONG!

REMOTE ANTENNA

MOUNT RECEIVER OR ANTENNA AS HIGH ABOVE

LOCATING A RECEIVER OR ANTENNA BELOW

(OPTIONAL)

EARTH LEVEL AS POSSIBLE

EARTH LEVEL WILL IMPAIR RANGE

ATTACH CASE WITH

TWO SCREWS IN

KEYHOLE SLOTS,

THEN SECURE CASE

WITH TWO BOTTOM

RIGHT

WRONG!

SCREWS

CENTRALLY LOCATE RECEIVER

TRANSMITTERS AT THE OTHER END OF

OR ANTENNA

HOUSE MIGHT BE TOO FAR AWAY

TX

Less

DOOR

than

DOOR

TRANSMITTER

3 ft.

Wall

CONNECT ANTENNA

above

MOUNTING WILL

3 ft.

Concrete

slab

TX

Concrete

Large

COAX DIRECTLY OR

Min.

EFFECT RADIO

slab

slab

TX

metal

USE UP TO 25 FEET

RANGE

floor

floor

appliance

(refrig.)

OF RG-59 COAX AS

RIGHT

WRONG!

WRONG!

AN EXTENSION

TERMINAL BLOCK DETAILS

TYPICAL CONTROL PANEL CONNECTION

S1 FORMAT TRANSMITTER DETAILS

SXR-64A TERMINALS

SXR-64A TERMINALS

SET CHANNEL AND

EACH S1 FORMAT

1

2 3

4

5

6

7 8 9

10

11

12

13

14 15

16

17 18 19

20

ZN1

COM

ZN2

ZN3

COM ZN4 ZN5 COM

ZN6

ZN7

COM ZN8

LB

STS COM TMP TST

ARM

TRANSMITTER MUST

SYSTEM SWITCH TO

1

2

3

4

5 6

7

8

9

10

11 12

13

14 15 16 17

18 19 20

BE SET TO A DIFFERENT

ANY UNIQUE CODE

CODE

ZN1

COM ZN2

ZN3

COM

ZN4

ZN5 COM ZN6

ZN7

COM ZN8

LB

STS COM TMP

TST

ARM

OUTPUTS PROGRAMMED

FOR NORMALLY OPEN

CHANNEL

END-OF-LINE

SWITCH

RESISTORS

MODEL ST-1

ZONE OUTPUTS

MODEL ST

STATUS

JUMPER

FOR CONNECTION TO ALARM ZONE INPUTS ON THE ALARM

CONTROL PANEL. ZONE OUTPUT WILL ACTIVATE WHEN ANY

RESTORE

TRANSMITTER CHANNEL PROGRAMMED FOR THAT ZONE IS

JUMPER

IN THE FAULTED (ALARM/OPEN) CONDITION ("O" DISPLAYED

SYSTEM

ON THE CONDITION DISPLAY).

CUT ST-1 JUMPERS

SWITCH

SYSTEM

CHANNEL

LOW BATTERY OUTPUT

SWITCH

TO ENABLE STATUS

SWITCH

FOR CONNECTION TO A TROUBLE ZONE ON THE ALARM

& RESTORE SIGNALS

CONTROL PANEL. OUTPUT WILL ACTIVATE WHEN ANY

TRANSMITTER CHANNEL DISPLAYS AN "L" ON THE

CONDITION DISPLAY.

ST-1 & 50S40A NOTE: SET SXR-64A TRANSMITTER OPTION "A"

STATUS OUTPUT

TO "ON" FOR THE CHANNEL THE TRANSMITTER IS PROGRAMMED TO.

FOR CONNECTION TO A TROUBLE ZONE ON THE ALARM

ALARM CONTROL PANEL

OTHERWISE, THE LONG ALARM AND RESTORE

CONTROL PANEL. OUTPUT WILL ACTIVATE WHEN ANY

TRANSMITTER CHANNEL DISPLAYS AN "S" ON THE

ZONE 8

TRANSMISSIONS WILL CAUSE A DOUBLE ZONE CLOSURE

CONDITION DISPLAY.

MODEL ST-23A

TAMPER OUTPUT

COMMON

SYSTEM

SWITCH

FOR CONNECTION TO A TROUBLE ZONE ON THE ALARM

ZONE 7

ST-23A NOTE: SET

CONTROL PANEL. OUTPUT WILL ACTIVATE WHEN ANY

AUXILIARY

MODEL 50S40A

TRANSMITTER CHANNEL DISPLAYS A "P" ON THE CONDITION

ZONE 6

SYSTEM SWITCH #1

POWER

DISPLAY OR WHEN ANY PROGRAMMING BUTTON IS

TO OFF

PRESSED WHILE THE SYSTEM IS ARMED.

COMMON

CHANNEL

TEST OUTPUT

ZONE 5

SWITCH

FOR CONNECTION TO A TEST ZONE ON THE ALARM

POWER INPUT

CONTROL PANEL. OUTPUT WILL ACTIVATE WHEN ANY

FOR CONNECTION TO THE ALARM

ZONE 4

TRANSMITTER THAT CAN SEND A TEST SIGNAL HAS ITS

TEST BUTTON PRESSED.

CONTROL PANEL'S AUXILIARY

POWER OUTPUT. POWER INPUT

COMMON

NOTES:

CAN BE FROM 11-16 VDC ONLY

ARMED

1. ALL COM TERMINALS ARE COMMON GROUND

ARMED INPUT

ZONE 3

OUTPUT 8

AND CONNECTED TOGETHER.

FOR CONNECTION TO THE ALARM

ZONE 2

CONTROL PANEL'S ARMED OUTPUT.

2. ALL OUTPUTS CAN BE PROGRAMMED FOR NORMALLY

WHEN UPGRADING AN SS-32,

SYSTEM

THE ARMED INPUT CAN BE SET FOR

COMMON

OPEN OR NORMALLY CLOSED OPERATION. EACH OUTPUT

ARMED-POSITIVE OR

SSR-32, OR SXR-64 INSTALLATION,

SWITCH

RETURNS TO ANY COM TERMINAL.

ARMED-NEGATIVE POLARITY.

ZONE 1

THE TRANSMITTER SWITCH

3. EACH OUTPUT CAN SWITCH UP TO 100 mA @ 24 VDC

CHANNEL

SETTINGS CAN REMAIN THE SAME

SWITCH

MAXIMUM.