6. SET RECEIVER SWITCHES

7. CONNECT POWER AND OUTPUTS

8. MOUNT ANTENNA AND ROUTE CABLE

OPTION SWITCH
CHANNEL TO RECEIVE

 

STATUS REPORTS

 

SWITCH 1

SWITCH 2

CH #

 

OPTION SWITCH 3

 

OFF

OFF

CH 1

 

OFF

NO STATUS REPORTS

 

ON

OFF

CH 2

 

REQUIRED FROM TX

 

OFF

ON

CH 3

 

ON

STATUS REPORTS

 

ON

ON

CH 4

 

 

REQUIRED FROM TX

 

 

 

 

 

 

 

 

SET SWITCHES 1 & 2 IN THE RECEIVER TO

 

 

 

 

SELECT THE CHANNEL NUMBER THAT THE

NOTE: OPTION SWITCH 4 IS UNUSED

TRANSMITTER IS GOING TO SEND

 

 

 

 

SYSTEM CODE SWITCHES

SET SYSTEM CODE SWITCHES A & B TO MATCH SYSTEM CODE SWITCHES A & B IN THE TRANSMITTER

USE 18-24 AWG WIRE
TO CONNECT POWER
AND OUTPUTS
ROUTE WIRES THROUGH CASESTRAIN RELIEF BUSHING BEFORECONNECTING TO TERMINALS
WARNING

THIS UNIT REQUIRES 12 VDC AT 1/2 AMP.

THE NO-LOAD VOLTAGE OF THE SUPPLY

MUST NOT EXCEED 17.5 VDC OR DAMAGE

USE ANT-1A ANTENNA FOR SHORT RANGE (LESS THAN 1 MILE)APPLICATIONS
ANT-1AANTENNACON-180A + CON-90AANGLE CONNECTOR
CON-180ASTRAIGHT CONNECTOR
SWITCH "A"

SWITCH "B"

 

OPTION SWITCH

 

 

+ 12VDC

LOWBAT

 

STATUS

 

TO THE UNIT WILL OCCUR!
GND

 

 

N/O

COM

N/C

GND

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RELAY OUTPUT WILL SWITCH
FROM 12 VDC, 1/2 AMPUP TO 1 AMP @ 32 VDC

 

REGULATED POWER SOURCE

 

 

LOW BATTERY & STATUS
RECEIVER CURRENT:OUTPUTS WILL SWITCH
UP TO 50 mA @ 20 VDC
<30 mA STANDBY
TO GROUND WHEN ACTIVE
<70 mA WITH RELAY ENERGIZED

 

USE 3-FOOT LONG ANT-2 ANTENNA FOR LONGERRANGE APPLICATIONS OR DIFFICULTINSTALLATIONSMOUNT ANTENNAS AS HIGH AS POSSIBLE(A METAL MOUNTING POLE IS RECOMMENDED)AN 18-FOOT RG-58 CABLE IS SUPPLIED WITH THEANT-2 KIT. UP TO 50 FEET OF RG-58 CAN BE USED.USE RG-8 FOR UP TO 100-FOOT CABLE RUNS. TO UNIT

9. TEST SYSTEM

10. COMPLETE INSTALLATION

LINEAR LIMITED WARRANTY

SLIDE BOARD INTO
CASE IN THE 3RD
SLOT UP

WARNING

NEVER CONNECT THE TRANSMITTER AND RECEIVER ANTENNA CONNECTORS DIRECTLY TO EACH OTHER. MAJOR DAMAGE TO BOTH UNITS WILL OCCUR!

INSTALL AND SETUP THE COMPANION UNIT AS DESCRIBED IN ITS INSTALLATION INSTRUCTIONS

SECURE END PLATE BYINSTALLING THE FOUR CASE SCREWSINSTALL THE TWO REMAINING MOUNTING SCREWS

This Linear product is warranted against defects in material and workmanship for twelve (12) months. The Warranty Expiration Date is labeled on the product. This warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of

Linear LLC for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties, including implied warranties for merchantability and implied warranties for fitness, are valid only until Warranty Expiration Date as labeled on the product. This Linear LLC Warranty is in lieu of all other warranties express or

TRANSMITTERRECEIVER
APPLY POWER AND TRIGGER THE

 

TRANSMITTER'S INPUT

 

THE TRANSMIT INDICATOR
THE RECEIVER'S SIGNAL
SHOULD LIGHT WHEN THE
INDICATOR SHOULD LIGHT AND
TRANSMITTER IS TRIGGERED
OUTPUT SHOULD ACTIVATE
IF SYSTEM FAILS TEST, CHECK POWER, SWITCH
SETTINGS AND ANTENNA CONNECTIONS
TIGHTEN WIRING STRAINRELIEF BUSHING TOSECURE AND WEATHERPROOF WIRINGTEST SYSTEM AGAIN AFTERCOMPLETING INSTALLATION
implied.

All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.

IMPORTANT !!!

Linear radio controls provide a reliable communications link and fill an important need in portable wireless signaling. However, there are some limitations which must be observed.

WARNING: THIS PRODUCT IS NOT TO BE USED IN LIFE SAFETY APPLICATIONS. FCC Rules allow unlicensed high-power transmissions at or near the operating frequency of this product which may interfere with, or even disable, normal operation of this radio device.

For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 95 Radio Control devices. As such, they have limited transmitter power and therefore limited range.

A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings.

Changes or modifications to the device may void FCC compliance.

Infrequently used radio links should be tested regularly to protect against undetected interference or fault.

A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users.

Copyright © 2004 Linear LLC

215183 C