6. SET RECEIVER SWITCHES
7. CONNECT POWER AND OUTPUTS
8. MOUNT ANTENNA AND ROUTE CABLE
|
|
|
| OPTION SWITCH |
| SWITCH # |
| CHANNEL # |
| SELECTION |
|
| |||
| SWITCH 1 |
| CH 1 |
| OFF = NO STATUS REPORTS REQUIRED FROM TX CHANNEL 1 |
|
| ON = STATUS REPORTS ARE REQUIRED FROM TX CHANNEL 1 | ||
|
|
|
| |
SWITCH 2 |
| CH 2 |
| OFF = NO STATUS REPORTS REQUIRED FROM TX CHANNEL 2 |
|
| ON = STATUS REPORTS ARE REQUIRED FROM TX CHANNEL 2 | ||
|
|
|
| |
SWITCH 3 |
| CH 3 |
| OFF = NO STATUS REPORTS REQUIRED FROM TX CHANNEL 3 |
|
| ON = STATUS REPORTS ARE REQUIRED FROM TX CHANNEL 3 | ||
|
|
|
| |
SWITCH 4 |
| CH 4 |
| OFF = NO STATUS REPORTS REQUIRED FROM TX CHANNEL 4 |
|
| ON = STATUS REPORTS ARE REQUIRED FROM TX CHANNEL 4 | ||
|
|
|
| |
|
| SET SWITCHES 1 | ||
|
| REQUIRE STATUS REPORTS FROM THE TRANSMITTER(S) | ||
|
|
|
|
|
USE 18-24 AWG WIRE
TO CONNECT POWER
AND OUTPUTS
ROUTE WIRES THROUGH CASE
STRAIN RELIEF BUSHING BEFORE
CONNECTING TO TERMINALS
| GND | 12+VDC | LOWBAT | STATUS | N/O | COM |
| N/C |
| N/O | COM |
| N/C |
| N/O | COM |
| N/C |
| N/O | COM |
| N/C |
|
|
|
|
| CH | 1 |
|
|
| CH | 2 |
|
|
| CH | 3 |
|
|
| CH | 4 |
|
USE
STRAIGHT CONNECTOR
| SWITCH "A" | SWITCH "B" |
|
| LOW BATTERY & STATUS |
|
| |
| OUTPUTS WILL SWITCH |
|
| |
| UP TO 50 mA @ 20 VDC |
| WARNING | |
| TO GROUND WHEN ACTIVE | |||
|
| ||
| FROM 12 VOLT, 1/2 AMP | THIS UNIT REQUIRES 12 VDC AT 1/2 AMP. | ||
| THE | |||
| POWER SOURCE | |||
| MUST NOT EXCEED 17.5 VDC OR DAMAGE | |||
| RECEIVER CURRENT: | |||
| <30 mA STANDBY | TO THE UNIT WILL OCCUR! | ||
|
| ||
| <190 mA WITH ALL RELAYS ENERGIZED |
| ||
TO UNIT
9. TEST SYSTEM | 10. COMPLETE INSTALLATION |
LINEAR LIMITED WARRANTY
SLIDE BOARD INTO
CASE IN THE 3RD
SLOT UP
WARNING 
NEVER CONNECT THE TRANSMITTER AND RECEIVER ANTENNA CONNECTORS DIRECTLY TO EACH OTHER. MAJOR DAMAGE TO BOTH UNITS WILL OCCUR!
INSTALL AND SETUP THE COMPANION UNIT AS DESCRIBED IN ITS INSTALLATION INSTRUCTIONS
INSTALLING THE FOUR CASE SCREWS
INSTALL THE TWO REMAINING MOUNTING SCREWS
This Linear product is warranted against defects in material and workmanship for twelve (12) months. The Warranty Expiration Date is labeled on the product. This warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of
Linear LLC for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties, including implied warranties for merchantability and implied warranties for fitness, are valid only until Warranty Expiration Date as labeled on the product. This Linear LLC Warranty is in lieu of all other warranties express or
TRANSMITTER | RECEIVER | |
APPLY POWER AND TRIGGER THE | ||
| ||
TRANSMITTER'S INPUT |
|
| THE TRANSMIT INDICATOR | THE RECEIVER'S SIGNAL |
| SHOULD LIGHT WHEN THE | INDICATOR SHOULD LIGHT AND |
| TRANSMITTER IS TRIGGERED | OUTPUT SHOULD ACTIVATE |
TIGHTEN WIRING STRAIN
RELIEF BUSHING TOSECURE AND WEATHERPROOF WIRINGTEST SYSTEM AGAIN AFTERCOMPLETING INSTALLATIONimplied.
All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Linear Technical Services at
IMPORTANT !!!
Linear radio controls provide a reliable communications link and fill an important need in portable wireless signaling. However, there are some limitations which must be observed.
WARNING: THIS PRODUCT IS NOT TO BE USED IN LIFE SAFETY APPLICATIONS. FCC Rules allow unlicensed
For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 95 Radio Control devices. As such, they have limited transmitter power and therefore limited range.
A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings.
Changes or modifications to the device may void FCC compliance.Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users.
| Copyright © 2004 Linear LLC | 215194 C |