6. SET TRANSMITTER SWITCHES
7. CONNECT POWER AND TRIGGER INPUTS
8. MOUNT ANTENNA AND ROUTE CABLE
SET OPTION SWITCH
RECEIVER BANK |
|
| STATUS REPORTS | |||
SWITCH 1 | SWITCH 2 |
| BANK # |
|
| SWITCH 3 |
OFF | OFF |
| 1 |
| OFF | NO STATUS REPORTS |
ON | OFF |
| 2 |
| ON | STATUS REPORTS |
OFF | ON |
| 3 |
|
|
|
ON | ON |
| 4 |
|
|
|
|
|
|
|
| AUTO RESTORAL | |
SET SWITCHES 1 & 2 TO SELECT THE | ||||||
RECEIVER BANK THE TRANSMITTER |
|
| SWITCH 4 | |||
ACTIVATES (USED ONLY FOR 16 CHANNEL |
| OFF | MANUAL RESTORE | |||
RECEIVER, USE BANK 1 FOR ALL OTHERS) |
| ON | AUTO RESTORE |
SYSTEM CODE SWITCHES
INPUT SELECT SWITCH |
| ||
SWITCH # | CHANNEL | OFF = | ON = |
SWT 1 | CH 1 | N/O | N/C |
SWT 2 | CH 2 | N/O | N/C |
SWT 3 | CH 3 | N/O | N/C |
SWT 4 | CH 4 | N/O | N/C |
SET SWITCHES 1 - 4 TO SELECT THE NORMAL
INPUT TRIGGER DEVICE |
|
SWITCH OFF = N/O | SWITCH ON = N/C |
SET INPUT SELECT SWITCH TO MATCH INPUT TYPE FOR EACH CHANNEL
USE
APPLICATIONS
ANTENNA
ANGLE CONNECTOR
STRAIGHT CONNECTOR
SET SYSTEM CODE SWITCHES A & B TO MATCH SYSTEM CODE SWITCHES A & B IN THE RECEIVER
SWITCH "A" | SWITCH "B" |
|
OPTION SWITCH
ROUTE WIRES THROUGH CASE
STRAIN RELIEF BUSHING BEFORE
CONNECTING TO TERMINALS
USE
TO CONNECT POWER
AND TRIGGER INPUTS
CAUTION: BE SURE WIRE STRANDS
DO NOT TOUCH NEARBY FUSE
| GND | + 12 VDC |
| GND |
|
| CH 1 | GND | CH 2 | GND | CH 3 | GND | CH 4 | |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| FOR RUNS LONGER THAN 3' CONNECT THE |
| |
|
| SUPPLIED 10K Ω RESISTOR FROM THE +12V | WARNING | |
|
| SUPPLY TO THE "INPUT" TERMINAL OF THE | ||
|
|
| ||
|
| SENSOR SWITCH |
|
|
|
| THIS UNIT REQUIRES 12 VDC AT 2 AMPS. | ||
|
|
| ||
FROM 12 VDC, | THE | |||
REGULATED POWER NOTE: MAXIMUM POWER WIRE | MUST NOT EXCEED 17.5 VDC OR DAMAGE | |||
SOURCE | RUN | TO THE UNIT WILL OCCUR! |
USE
RANGE APPLICATIONS OR DIFFICULT
INSTALLATIONS
MOUNT ANTENNAS AS HIGH AS POSSIBLE
(A METAL MOUNTING POLE IS RECOMMENDED)
AN
USE
TO UNIT
9. TEST SYSTEM | 10. COMPLETE INSTALLATION |
LINEAR LIMITED WARRANTY
SLIDE BOARD INTO
CASE IN THE 3RD
SLOT UP
WARNING
NEVER CONNECT THE TRANSMITTER AND RECEIVER ANTENNA CONNECTORS DIRECTLY TO EACH OTHER. MAJOR DAMAGE TO BOTH UNITS WILL OCCUR!
INSTALL AND SETUP THE COMPANION UNIT AS DESCRIBED IN ITS INSTALLATION INSTRUCTIONS
SECURE END PLATE BY
INSTALLING THE FOUR CASE SCREWS
INSTALL THE TWO REMAINING MOUNTING SCREWS
This Linear product is warranted against defects in material and workmanship for twelve (12) months. The Warranty Expiration Date is labeled on the product. This warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of
Linear LLC for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties, including implied warranties for merchantability and implied warranties for fitness, are valid only until Warranty Expiration Date as labeled on the product. This Linear LLC Warranty is in lieu of all other warranties express or implied.
TRANSMITTER | RECEIVER | |
APPLY POWER AND TRIGGER THE | ||
| ||
TRANSMITTER'S INPUT |
|
THE TRANSMIT INDICATOR | THE RECEIVER'S SIGNAL |
SHOULD LIGHT WHEN THE | INDICATOR SHOULD LIGHT AND |
TRANSMITTER IS TRIGGERED | OUTPUT SHOULD ACTIVATE |
IF SYSTEM FAILS TEST, CHECK POWER, SWITCH
SETTINGS AND ANTENNA CONNECTIONS
TIGHTEN WIRING STRAIN
RELIEF BUSHING TO
SECURE AND WEATHER
PROOF WIRING
TEST SYSTEM AGAIN AFTER
COMPLETING INSTALLATION
All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Linear Technical Services at
IMPORTANT !!!
Linear radio controls provide a reliable communications link and fill an important need in portable wireless signaling. However, there are some limitations which must be observed.
WARNING: THIS PRODUCT IS NOT TO BE USED IN LIFE SAFETY APPLICATIONS. FCC Rules allow unlicensed
For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 95 Radio Control devices. As such, they have limited transmitter power and therefore limited range.
A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings.
Changes or modifications to the device may void FCC compliance.
Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users.
Copyright © 2005 Linear LLC | 215284 C |