Getting started with Logitech Alert™ 750i
Master System
1 | 2 | 3 | 4 | 5 | 6 |
7 | 8 | 9 | 10 |
12 13
|
| LogitechAlert |
| |
|
|
| ™ |
|
|
|
| System |
|
|
|
| VideoSecurity |
|
11 |
|
|
|
|
| KNOW | |||
| guide | |||
| ™ |
|
| GETTINGTO |
guide | SystemRequirements |
| ||
&SupportGuide |
| |||
|
| |||
1 | Logitech Alert Camera | 6 Mounting accessories | 11 Power supply cable extender | ||
2 | Software install CD | 7 | Camera power supply | 12 | System Requirements Guide |
3 | Power supply cable (yellow tips) | 8 | Network adapter | 13 | Getting to Know Guide |
| 4 microSD™ card adapter | 9 | Network adapter cable (blue tips) |
|
| |
5 | Desktop stand | 10 Suction cup |
|
| |
!
Legal Warning
Certain uses of security camera products and audio devices, such as employee monitoring, surreptitious viewing and recording of images and/or audio, or the use, publication or distribution of image and/or audio recordings, are prohibited or restricted by country, state and local laws.
Be sure to comply with the laws in your country, state, and locality when using Logitech Alert products and services.
Before you begin...
1)Read all instructions before beginning the installation.2)During installation, we will test your PC’s firewall settings. If prompted toallow Logitech Alert access to the network, you should always answer “Yes” or “Allow.”
Are you going to run Logitech WiLife & Logitech Alert Systems Simultaneously?
Read special notes at www.logitech.com/security/legacyNetwork Adapter / Power Supply Install Note
Do NOT plug the network adapter or power supply into a surge protector or power strip as they interfere with the cameras. Surge protectors are
The network adapter and power supply must be plugged directly into your wall outlet.
1Install Software
!Internet access is required for installation.1)Insert the Software Install CD and follow the instructions during the install.
• The installer will check for the latest version of the software.Alternatively, you can download the latest version atwww.logitech.com/downloads.2)You may be asked to reboot the PC.3)Logitech Alert Commander software will open.4)The First Run Wizard will guide you through the next steps of setup.2 Plug in Network Adapter |
|
| 3 Plug in Your Camera |
|
|
| When prompted to plug in the network adapter: |
|
| When prompted to connect your camera: |
|
|
1) Plug one end of the blue cable connector into the network adapter. | 1a) Then, plug the network adapter into the power outlet. | 1) Remove the hatch from the back of the camera. 1a) Plug the yellow cable connector into the port. | 1b) Use the lock slider to lock the connector in place. | ||
| 2) Connect the other blue cable connector into an open port on your router. |
| 2) Plug the yellow cable connector into the power supply port. 2a) Plug the power supply into an outlet near the PC where the software is installed. | |||
|
|
| 1 | 1a |
|
|
|
|
| 2 | 2a |
|
| INTERNET | 1b |
|
|
|
|
|
|
| |
|
|
| 1 |
|
|
|
|
| 2 |
|
|
|
|
| 3 |
|
|
|
|
| 4 |
|
|
1 | 1a | 2 | (not included) |
|
|
Shortly after connecting, your camera will appear in Alert Commander software. You can now move the camera to its desired location.
4Choose Your Camera Location
OR
On a window looking out or inClean the window's surface and the inside area of the suction cup before applying it to the window. Periodically press the suction cup against the glass to strengthen its bond to the window.
You can use the
Wall/Ceiling Mounting Instructions
The wall mount allows you to easily fasten your camera to a ceiling or wall. 1) Start by
1 | 3 |
|
2 | OR |
|
(optional)