Congratulations!

You have completed the basic setup.

Refer to the Getting to Know Guide to read about additional features and functions.

Alert

 

Logitech

 

 

System

Security

Video

 

 

Quick-start

 

guide

TOKNOW

 

 

GETTING

Reading the Diagnostic LEDs

FAQs

Where can I find more information?

 

What do I do if the power supply cable (yellow connector) is too short?
Commander Help
HELP

To lengthen, either use a coupler or purchase a longer ethernet (CAT-5e) cable.

You can press the F1 key from any screen in the Alert

 

 

 

Commander to access the online Help system.

 

 

Knowledge Base

 

 

Troubleshooting help is available at www.logitech.com/support

 

 

Customer Support

 

 

Call 1.888.469.4543

 

 

Refer to System Requirements Guide.

 

 

 

Alert 700i/750i

Want to see more FAQs?

Quick-startLogitech

guide

SystemRequirements

 

 

Guide

 

 

 

&Support

 

Go to www.logitech.com/security/support
Troubleshooting camera connection:What if camera/video disappears?1)Test another outlet for your camera, perhaps one closer to your PC.

2)Verify that the camera power supply and the network bridge are plugged directly into a power outlet and not a power strip.

3)Check firewall settings or press the F1 key in Commander Software for additional help.

4)Go to Settings > Cameras > Add/Find > Find Cameras.5)Reset the camera. See instructions in “Camera Reset Instructions.”

Camera Reset Instructions

Insert a paper clip into the reset hole located on the back of the camera and press gently and then release.

If the camera does not appear after reset, go to Settings > Cameras > Add/Find > Find Cameras. If the camera still does not operate, contact technical support.

Resetting the camera will restore the camera to factory settings. However, it will not delete video recorded on the microSD card.

Motion LED
How do I know the camera is recording?
Camera is ready to record (Red)Camera is recording (Red, blinking)
Turning Off Motion and Diagnostic LEDs
You can turn off the motion and diagnostic LEDs in theSettings > Cameras > Camera > Show LED for....See F1 Help for instructions.
Camera Diagnostic LED
Which LED colors indicate “camera is working”?
Connected to Internet (Green)Connected to Alert Commander (Purple)Connected to Alert Commander & Internet (Blue)Upgrading Firmware (White)Camera in standalone mode (Yellow)Not connected to Alert Commander or Internet (Light Blue)

Camera Diagnostic LED

Which LED colors indicate “camera is not working”?
Camera boot-up failed * (Red blinking)

microSD card read/write failure - No microSD card * (Alternating Red / Yellow, blinking)

* See Camera Reset Instructions for assistance.
Power Supply / NetworkPower Supply Network

 

Adapter Diagnostic LEDsStatus LEDs (Top)

 

What do these LEDs tell me?
What do these LEDs tell me?

Traffic and data is flowing (Green)

Link to Power Supply

(Green)

Connection with Ethernet/LAN

Shows network traffic

(Blue)

(Yellow)

 

 

LED

OFF ON

On/Off switch for Power Supply / Network Adapter LEDs
How do I turn these LEDs off?

Use the switch located on the side of the power supply or network adapter to disable these diagnostic LEDs.

www.logitech.com

© 2010 Logitech. All rights reserved. Logitech, the Logitech logo, and other Logitech marks are owned by Logitech and may be registered. All other trademarks are the property of their respective owners. Logitech assumes no responsibility for any errors that may appear in this manual. Information contained herein is subject to change without notice.

Using the microSD™ card adapter

NOTE: Unplug the camera before removing, replacing, or upgrading your microSD card.

To review the video on the microSD card, we recommend you using Logitech Alert Commander.

To review the video on the microSD card without Logitech AlertCommander:
1) Open the hatch on the bottom of the camera and remove the microSD

1

2

3

card from its port.

 

 

 

2) Plug the microSD card into the adapter.

 

 

SMARTMEDIA

 

3) Plug the adapter into the PC’s SD card slot.

COMPACT

FLASH I/II

 

 

MMC/SD

 

 

 

 

 

 

 

 

MS/MS

• View video recordings using the free Apple QuickTime player or other

 

 

PRO

 

 

 

player that supports H.264 video playback. (To download QuickTime, visit

 

 

 

http://www.apple.com/quicktime/download/)

 

 

 

!

occur.microSD card must be installed in the camera for recording to

 

 

 

620-001963 rev004

microSD Logo is a trademark of SD-3C, LLC.