FCC REGISTRATION AND REPAIR INFORMATION
Your new Lucent Technologies telephones have been registered with the Federal Communications Commission (FCC). This product complies with standards in Part 68 of the FCC rules. The FCC requires us to provide you with the following information:
CONNECTION AND USE WITH THE NATIONWIDE TELEPHONE NETWORK
•Where the telephone equipment requires ac power, plug the tele- phone into a different ac outlet so that the telephone equipment and receiver are on different branch circuits.
LUCENT TECHNOLOGIES WARRANTY INFORMATION
WHAT IS COVERED: All terms and conditions specified in your
to be connected to a telephone loop which is used by the device, to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the sum of the Load Numbers of all the devices does not exceed 100.
To program the HOLD button as an alternate feature such as Call Park
1 | Press the PROGRAM button; then press the FLASH button; then |
| press the HOLD button. |
2 | Press “797 (SYS)” on the dial pad. |
3 | Press the FLASH button again; then press the PROGRAM button |
| again. |
The FCC requires that you connect your telephone equipment to the nationwide telephone network through a modular telephone outlet or jack. The modular telephone outlet or jack to which the telephone must be connected is a USOC RJ11C or RJ11W. The telephone may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs. (Contact your state public utility commission or corporation commission for information.)
INFORMATION FOR THE TELEPHONE COMPANY
Upon request of your local telephone company, you are required to provide them with the following information: A.) Your phone number. B.) The telephone equipment's FCC registration number and ringer equivalence number (REN). These numbers are on the back or bottom of your telephone equipment. The REN is useful to determine how many devices you may connect to your telephone line and still have them ring when your telephone line is called. At most, but not all areas, the sum of all Rent should be 5 or less. You may want to contact your local telephone company.
REPAIR INSTRUCTIONS
If it is determined that your telephone is malfunctioning, the FCC requires that it not be used and that it be unplugged from the modular outlet until the problem is corrected. Repairs can only be made by the manufacturer or its authorized agents or by others who may be authorized by the FCC.
agreement with Lucent Technologies apply.
TO GET WARRANTY SERVICE FOR YOUR TELEPHONE: Call the Lucent Technologies Customer Service
Support Operations toll-free at 1 800 242-2121 or call the distributor from whom the product was purchased. If you are directed to ship your telephone to an authorized service location, you must prepay all shipping costs. We suggest that you retain the original packing material in the event you need to ship the unit. When sending your telephone to a service location, include your name, address, phone number, proof of purchase (or original shipping receipt), and description of the operating problem. After replacing your telephone, Lucent Technologies will ship it to you at no cost to you.
CANADIAN REGULATIONS
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the Department of Communications.
NOTICE: The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain
APPARATUS CODE
8101A01B
8101A02B
8102A01C
8103
8104
8110A01D
8111
CANADIAN LOAD NUMBER
20
20
17
10
NETWORK INTERFACES
CA11A, CA114A; RJ11C, RJ14C
CA11A, CA114A; RJ11C, RJ14C
CA11A, CA114A; RJ11C, RJ14C
CA11A, CA114A; RJ11C, RJ14C
CA11A, CA114A; RJ11C, RJ14C
CA110A, CA114A; RJ11C, RJ14C
CA110A, CA114A; RJ11C, RJ14C
Note: Next, you must program the button with the feature access code of the alternate feature (such as Call Park).
Note: As long as the HOLD button is not being used for the Hold feature, the light next to the HOLD button will not go on.
The Timed Disconnect Feature
The system manager can program a minimum of 1.2-second timed disconnect. The default setting is timed disconnect disabled.
Note: If Timed Disconnect is enabled, there will be a 1.2-second delay in speakerphone response.
To program the (1.2-second minimum) Timed Disconnect option
1Press the PROGRAM button; then press the FLASH button.
2Press “837 (TDS)” on the dial pad.
3Press the FLASH button again; then press the PROGRAM button again.
To disable the Timed Disconnect option
1 Press the PROGRAM button; then press the FLASH button. |
RIGHT OF THE TELEPHONE COMPANY
If telephone equipment is causing harm to the telephone network, the telephone company may temporarily discontinue your telephone service. If possible, they'll notify you before they interrupt service. If advance notice isn't practical, you'll be notified as soon as possible. You'll be given the opportunity to correct the problem, and you'll be informed of your right to file a complaint with the FCC. Your telephone company may make changes in its facilities, equipment, operations or procedures that could affect the proper functioning of your Lucent Technologies product. If such changes are planned, you'll be notified.
INTERFERENCE INFORMATION
WARNING: Some telephone equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. These telephones have been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation.particular installation.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient the receiving television or radio antennae where this may be done safely.
•To the extent possible, relocate the receiver with respect to the tele- phone equipment.
telecommunications network protective, operational and safety requirements. The Department does not guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electrical inspection authority, or electrician, as appropriate.
NOTICE: The Load Number (LN) assigned to each terminal device denotes the percentage of the total load
FOR THE SYSTEM MANAGER ONLY
(for the 8102M, 8104, 8110M, and 8111 telephones)
CAUTION: The following features for the
8102M, 8104, 8110M, and 8111 telephones should be programmed only by the system manager.
If necessary, detach this panel from the quick reference guide and keep it separate.
The Hold Feature
The Hold button ( Hold ) can be programmed, at each individual set, either as the normal Hold feature or as an alternate feature such as Call Park. The default setting is for normal Hold.
To program Hold for normal Hold (that is, the feature which allows the user to put a call on hold)
1Press the PROGRAM button; then press the FLASH button; then press Hold .
2 Press Hold again; then press the FLASH button again; finally, press the PROGRAM button again.
2 | Press “866 (TNO)” at the dial pad. |
3 | Press the FLASH button again; then press the PROGRAM button |
| again. |
Locking the Programmable Dialing Buttons
The system manager can lock the 12 programmable dialing buttons so the numbers or features assigned to these buttons CANNOT be changed.
To lock the Programmable Dialing buttons
1Press the PROGRAM button; then press the FLASH button.
2Press “752 (RLC)” on the dial pad.
3Press the FLASH button again; then press the PROGRAM button again.
To unlock the Programmable Dialing buttons
4Press the PROGRAM button; then press the FLASH button.
5Press “766 (RNO)” on the dial pad.
6Press the FLASH button again; then press the PROGRAM button again.
