HOOKUP DIAGRAMS

SRM450

SRM450

C300

C300

Plays the Mid and

Plays the Mid and

Plays the Mid and

Plays the Mid and

High Frequencies

High Frequencies

High Frequencies

High Frequencies

 

 

Full

Full

 

 

Range

Range

Pole

Power

Pole

Power

SRS1500

 

 

Mount

Cord

Mount

Cord

 

 

Line-Level

 

Line-Level

 

Plays the Low

 

Mid/High

 

Mid/High

 

Frequencies

ACTIVE

 

Out Left

 

Out Right

 

 

 

 

ACTIVE

 

ACTIVE

 

 

 

 

 

Full

Full

 

 

 

Power

 

Range

Range

 

 

 

 

 

 

 

Cord

 

Left

Right

 

 

 

 

 

 

 

 

 

 

 

 

 

Line-Level

 

 

 

 

 

Hi-Pass Out

 

SRS1500

Power

SRS1500

Power

 

 

 

Plays the Low

Plays the Low

 

 

Power

Frequencies

Cords

Frequencies

Cords

 

Stereo Power

 

 

 

 

 

Amplifier

Cord

2 SRS1500S WITH 2 SRM450S

 

1 SRS1500 WITH STEREO AMPLIFIER AND 2 C300S

CONNECTIONS

The SRS1500 has two female XLR inputs that accept a balanced line-level signal. When connecting a balanced signal, be sure it’s wired per AES (Audio Engineering So- ciety) standards:

 

 

 

 

 

 

 

 

 

XLR

Hot (+)

 

Pin 2

Cold (–)

 

Pin 3

Shield (Ground)

 

Pin 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

There are also four male XLR connectors labeled THRU (FULL RANGE OUTPUT) and HIGH PASS (MID/HIGH FREQ) OUTPUT. These are also wired according to the AES standard.

The THRU output connectors allow you to connect more than one SRS1500 to your system. Simply plug the signal source (i.e., mixer output) into the first speaker’s FULL RANGE INPUT jacks, and patch that speak- er’s THRU jacks to the next speaker’s INPUT jacks, and so on, daisy-chaining multiple speakers.

The THRU jack is wired straight from the FULL RANGE INPUT connector — there is no electronic circuitry between — so the signal coming out of the THRU jack is exactly the same as the signal going in.

The HIGH PASS OUTPUT jacks provide a line-level signal of the frequencies above 120Hz that you connect to a pair of active speakers (or to a stereo amplifier powering a pair of passive speakers). See the diagrams on the rear panel of the SRS1500 for additional connection information.

Balanced XLR Connectors

5