1. INTRODUCTION

Thank you for purchasing the Marantz MM9360 or MM9340 power amplifier for your sound system. Please take a few minutes to read this manual thoroughly, before you attempt connections and operations.The illustrations used in this manual refer to the six channel MM9360, but the MM9340 operates in the same manner, only with four channels and more power per channel.

This Marantz appliance is a Multi channel power amplifier, that is designed for home theatre and high quality audio systems.

2. FEATURES

The MM9360 is a six channel power amplifier, and the MM9340 is a four channel power amplifier developed for use in hi-fi AV systems.

- It is a high-power amplifier with efficient MOSFET high- speed switching output stages, controlled by internal mi- croprocessor and DSP algorithms. Rated outputs per channel are 150W / 8 ohms for the MM9360 and 275W / 8 ohms for the MM9340.

-It is provided with the MARANTZ RC-5 remote control capability so its power can be controlled from a MARANTZ preamplifier or surround receiver (MARANTZ remote con- trol compatible products).

-The power amplifier is equipped with LED indicators for signal present, peak power, thermal status, and protect mode for each channel.

6 C H P O W E R A M P L I F IE R M M 9 3 6 0

-The power amplifier will accept RCA, 1/4" jack, or XLR input connectors.

3. NAMES AND FUNCTIONS

1. SIGNAL indicator

The signal present LEDs illuminate at an input level of about 13mVrms (-35.5dBu).

2. PEAK indicator

The clipping LEDs illuminate at an input level of about 870mVrms (+1.0dBu), with all channels driven by 1KHz into 8Ω. This indicates that the signal processing circuitry has determined output levels to be approaching the available power supply rails and has begun to “soften” signal peaks. Actual onset of “hard” clipping depends on audio program and total load impedance and does not occur until the sig- nal processing circuitry can no longer compensate, which means that signal integrity can be maintained even if the clipping indicators illuminate for short periods of time.

3. THERMAL indicator

The thermal LEDs illuminate when the temperature of any one of the heat sink extrusions reaches 85 to 90°C. Both channels of the affected amplifier module will shut off until the measured temperature drops below about 70°C. The amplifier should be able to maintain proper operation at an ambient room temperature of 50°C (122°F) or less with typical audio program and all channels driven into 4Ω.

1

2

3

4

5

6

R

L

L

L

L

L

L

E

E

E

E

E

E

E

W

ANN

ANN

ANN

ANN

ANN

ANN

P

 

 

 

 

 

 

O

H

H

H

H

H

H

 

C

C

C

C

C

C

 

PR OT ECT

TH ER MA L

PEA K

SIGN A L

￿ ￿ ￿ ￿

￿

PO W ER

O FF

O N

￿

4

Page 3 Page 5
Page 4
Image 4
Marantz MM9360 manual Introduction, Features, Names and Functions
Page 3 Page 5

MM9360 specifications

The Marantz MM9360 is a high-performance power amplifier designed to deliver exceptional audio fidelity to music enthusiasts and home theater aficionados alike. Built on the foundation of Marantz's legacy in high-end audio, the MM9360 brings together innovative technologies and meticulous craftsmanship, making it an ideal choice for those seeking to enhance their audio experience.

One of the standout features of the MM9360 is its powerful output, capable of delivering 180 watts per channel into 8 ohms and 250 watts per channel into 4 ohms. This ensures that the amplifier can easily drive a wide range of speakers, from sensitive bookshelf models to larger floor-standing designs. The amplifier’s robustness allows it to handle dynamic musical passages without distortion, allowing listeners to enjoy their favorite tracks with clarity and impact.

The design of the MM9360 reflects Marantz's commitment to high-quality construction. It utilizes a fully discrete current feedback amplifier configuration, which minimizes feedback and distortion while enhancing transient response. This results in a natural sound characteristic that faithfully reproduces the original recording, making it a favorite among purists.

In terms of connectivity, the MM9360 is equipped with balanced XLR inputs as well as RCA inputs, offering flexibility for integration into various audio setups. The rear panel features sturdy binding posts to accommodate speaker connections securely. Additionally, the amplifier utilizes a sophisticated power supply, designed to handle peak demands efficiently and provide clean power to all connected components.

Another significant characteristic of the MM9360 is its low noise operation, achieved through careful component selection and layout. This attention to detail ensures that even the faintest nuances in a performance are not lost in unnecessary background noise, allowing listeners to fully immerse themselves in the audio experience.

The Marantz MM9360 also comes with a robust protection circuit that safeguards the unit and connected speakers from issues like overheating or short circuits. This feature adds an extra layer of reliability and peace of mind for users, allowing them to enjoy their music without worry.

In summary, the Marantz MM9360 is a powerful, versatile, and beautifully crafted amplifier that exemplifies the brand’s dedication to high-fidelity audio. Its combination of cutting-edge technologies, robust design, and sound engineering makes it an outstanding choice for any audio system, bringing the listener closer to the true essence of music. Whether used in a stereo setup or as part of a home theater, the MM9360 promises to elevate the listening experience to new heights.
Top Page Image Contents