English
CONTROLS, CONNECTORS,
AND INDICATORS
(Figure 2)
qPHONO INPUT JACKS
Connect the output jacks of a turntable to these jacks.
wGND (GROUND) TERMINAL
Connect the grounding wire from the turntable to this terminal.
eCD PLAYER INPUT JACKS
Connect the output jacks of a Compact Disc player to these jacks.
rTUNER INPUT JACKS
Connect the output jacks of the tuner to these jacks.
tAUX/DVD INPUT JACKS
These are auxiliary input jacks which can be used to connect the audio outputs of AV components such as DVD players, TV multiplex/stereo audio tuners, VCRs, and laserdisc players.
yMD/TAPE IN/OUT JACKS
Connect the play (output) jacks and record (input) jacks of MD or tape decks to these jacks.
u
Connect the play (output) jacks and record (input) jacks of CD Recorder to these jacks.
iSPEAKER SYSTEMS 1 / 2 TERMINALS Connect your speaker system(s) to these terminals.
oREMOTE CONTROL BUS TERMINALS
(REMOTE CONT. BUS)
Another item of audio equipment with a remote control bus terminal can be connected to these terminals by using a special- purpose cable. The bus OUT terminal is used to send signals to another item of equipment. The bus IN terminal is used to receive signals from another item of equipment.
!0POWER CORD
Connect to a household power outlet.
!1POWER SWITCH
Pressing once switches the power ON, and pressing again switches it OFF.
The POWER indicator lights when the POWER switch is ON, and go out when the POWER switch is OFF.
!2INPUT SELECTOR
Selects the program source to be recorded or played from the PHONO, CD, TUNER, AUX/DVD, MD/TAPE, and
!3STAND BY INDICATOR
Lights up when the unit is in the
!4TONE DEFEAT SWITCH
¡When the switch is not depressed, the audio signals are applied to the tone control circuit and the tone can be adjusted using the tone control knob.
¡When the switch is depressed, the audio signals bypass the tone control circuit and the tone control knob does not function.
!5MUTING INDICATOR
Light up when the MUTING button in the remote control unit is pressed.
NOTE:
Be sure to check the VOLUME control setting before pressing this switch to cancel muting. If the muting is canceled while the volume setting is high, the speakers could be damaged.
!6LOUDNESS SWITCH
The LOUDNESS switch compensates for human hearing char- acteristics by boosting the bass and treble response at low volume levels to achieve a more pleasing tonal balance.
!7VOLUME CONTROL
Adjusts the volume level. Turn the knob clockwise to increase the volume.
!8BALANCE CONTROL
Turn the knob to correct an unbalanced program source such as stereo broadcast or to vary the output level of the left or right channel. Note that, if the BALANCE control is turned fully in one direction, the sound will not be heard from the speaker on the other side.
!9SPEAKERS 1 / 2 SWITCHES
These switches are used to select the speaker system(s) connected to the SPEAKER SYSTEM 1 / 2 terminals on the rear panel. If both the 1 and 2 switches are pressed to the low positions, two speaker systems can be used at the same time. When headphones are used for listening, set both switches 1 and 2 to OFF (high positions).
@0BASS AND TREBLE TONE CONTROLS
Adjusts the tone by controlling the levels of two frequency bands. Turn each control toward (+) to enhance the corresponding frequency band, or toward
TREBLE: Adjusts the high frequency level.
BASS: Adjusts the low frequency level.
@1REC SELECTOR SWITCH
Selects the tape dubbing mode between tape decks or the signal output at the REC OUT jacks.
@2REMOTE SENSOR
The remote sensor receives the infrared commands from the remote control unit. When an infrared signal is received from the remote control unit. The remote control unit must always be pointed directry at the remote sensor.
@3PHONES JACK
Insert the standard phone plug of the headphones into this jack.
5
