Remote Control Operation

ENGLISH	REMOTE CONTROL OPERATION

	OPERATION

	The provided remote control unit is a universal remote controller. The
	POWER button x, numeric buttons . and control buttons ⁄2are used
	in common across different input source components.
	The input source controlled with the remote control unit changes when
	one of the input selector buttons c is pressed.
	• Example: To select the DVD as the input source and play the DVD
	player.
	Press the DVD button c twice within 2 seconds.
	The input selector of the SR5300 is switched to DVD and
	the remote control unit is set for control of the DVD player.
	Press the PLAY button on the remote controller .

FUNCTION AND OPERATION

zTransmitting indicator

Lights up during a button is pressed and an infrared signal is sending.

x(Main) POWER buttons

Press to switch the power of the SR5300 ON or OFF after pressing the AMP button c.

cInput selector buttons/ FUNCTION SELECTOR buttons (AUDIO/VIDEO

INPUT)

Press one of these buttons once or twice to select a particular source component. For example, to set the receiver to the DVD input, press the DVD button twice within 2 seconds.

Note:

•CDR/MD button is set CDR function at initial. To switch MD

function, press and hold down CDR/MD button and press 2 button ..

•To return CDR function, press and hold down CDR/MD button and press 1 button ..

v MAIN VOLUME UP ) /DOWN ( ) buttons

Main volume control of the SR5300. The front, surround, center and subwoofer channel volumes controlled by these buttons simultaneously.

bMUTE button

Muting button of the SR5300. Press this button decrease the sound temporarily . Press this button again to return to the previous sound.

nMENU button

This button is used to enter the SETUP MAIN MENU.

mCursor buttons ( , , , , OK)

Use these button when operating the SETUP MAIN MENU. See page 16.

,MENU OFF button

This button is used to exit from the SETUP MAIN MENU.

.Numeric buttons 1 to 9 (A, B, C ... Z, –) /

Surround mode buttons

Numeric buttons

These buttons are used to enter figures in the selection of a tuner preset station and station name preset or to set select a CD track number, etc. The functions of these buttons are dependent on the function button selected.

Surround mode buttons (when AMP mode is selected)

These buttons are used to select the surround mode.

⁄0P.SCAN (preset scan) button (when TUNER

mode is selected)

This button is used to start preset scan when SR5300 is selected TUNER mode.

⁄10 / A/D button

0 button

This button is used to enter the number “0”

A/D button (when AMP mode is selected)

This is used to switch between the analog and digital inputs.

⁄2CONTROL buttons

These buttons are used when operating the CD player, TAPE deck, etc. The function of these buttons are dependent on the function button selected.

For the controllable functions of each input function, please refer to fol- lowing table.

VCR

DVD

DSS

TUNER

TAPE

CDR

CHANNEL/SKIP

CH–

CHANNEL/SKIP

CH+

TUNE/SERCH

REWIND

TUNING–

REWIND

TUNE/SERCH

TUNING+

REC

MODE

DIRECTION

PAUSE

DISP./RDS

DISPLAY

PLAY

FRQ.

PLAY

F.DIRECT

DIRECT

+/A/ANT

VIDEO

TV/VCR

DISC +

DSS/VCR

DISC +

DECK A

–/B/VCR

VIDEO

TV/VCR

DISC +

DSS/VCR

DISC –

DECK B

STOP

PTY

⁄3ATT (attenuator) button

When the input signal is too high and the voice distorts even by throt- tling the SR5300 VOLUME control, turn on this function. “ATT” is indi- cated when this function is activated.

The input level is reduced. Attenuator is invalid for use with the output signal of “REC OUT”.

⁄4TREBLE UP ( ) /DOWN ( ) buttons

These buttons are used to adjust the tone control of high frequency sound for left, center and right speaker.

⁄5BASS UP ) /DOWN ( ) buttons

These buttons are used to adjust the tone control of low frequency sound for left, center right and subwoofer speaker.

⁄6MEMO button

Memory enable button for various preset functions.

Marantz SR5300 manual Remote Control Operation

Models: SR5300