2 5, English, Using the remote control unit

(Using the remote control unit)

PRESET SCAN

4. “xx CLEAR” appears on the display to indicate that

1. Recall the preset number to be inputted name

1. Tune into the radio station you desire (Refer to the “MANUAL TUNING” or “AUTO TUNING” section).

2. Press the MEMO button on the remote. “– –“ (preset number) starts blinking on the display.

3. Enter the desired preset number by pressing the numeric buttons.

Note:

•When entering a single digit number (2 for example), either input “02” or just input “2” and wait for a few seconds.

RECALLING A PRESET STATION

PAGE 2

TUNER CD CD-RMD

TAPE	AUX1	AUX2	AMP
		LIGHT
1			2
		RC1400
	Learning Remote Controller

2.

PAGE 2 4

7.1CHATT

4 5

DISPOSD

7 8

CLEAR0

SPK-AB

SLEEP

MEMO

4.

the specified preset number has been cleared.

Notes:

•To clear all stored preset stations, press and hold the CLEAR and the F/P buttons for two seconds.

SORTING PRESET STATIONS

SELECTOR

DOWN

	CLEAR		TUNING	F/PF/P		MODE
TV	DVD	VCR1		TAPE	CD	TUNER

AUX1 INPUT

with the method described in “Recalling” a preset station.

2. Press the MEMORY button on the front panel or press the MEMO button on the remote for more than 3 seconds.

3. The left most column of the station name indicator flashes, indicating the character entry ready status.

4. When the SELECT knob is turned, or press

the > button until PAGE2 is displayed and

press the SCAN+ (D1) or SCAN– (D2) on the

remote, alphabetic and numeric characters will

be displayed in the following order:

ENGLISH

2.1.

SELECTOR

	CLEAR		TUNING	F/P	MODE	DOWN	UP
TV	DVD	VCR1		TAPE	CD	TUNER

AUX1 INPUT

(Using the remote control unit)

1. Press the TUNER button twice within two seconds on the remote.

2. Press the > button until PAGE2 is displayed and press the P-SCAN (D4) on the remote. “PRESET SCAN” appears on the front display and then the preset station with the lowest preset number is recalled first.

3. Preset stations are recalled in sequence (No.1

→No.2 → etc.) for 5 seconds each.

If you have stations memorized, and there is a gap in the sequential order:

I.e. the stations are stored as follows

1)87.5 MHz

2)93.1 MHz

3)94.7 MHz

10)105.9 MHz

A → B → C ... Z → 1 → 2 → 3 ..... 0 → – → +

→ / → (Blank) → A

UP →

← DOWN

5. After selecting the first character to be entered,

press the MEMORY or ENTER buttons, press

the MEMO button on the remote.

The entry in this column is fixed and the next

column starts to flash. Fill the next column the

same way.

TUNER	CD	CD-R	MD	1.
TAPE	AUX1	AUX2	AMP
		LIGHT
1			2
		RC1400
	Learning Remote Controller

(Using the SR8400)

PAGE 2 4

D1
D2
D3
D4	3.
D5	3.
	2.

No stored preset number will be skipped.

4. You can fast forward the preset stations, press the > button until PAGE4 is displayed and press the P-SET+ (D4) continuously.

5. When the desired preset station is received, cancel the preset scan operation by pressing the CLEAR button or P-SCAN (D4) on the remote.

(notice there is no stations programmed for pre sets for 4-9), you can have pre set 10 become pre set 5:

To sort the numbers, press and hold the MEMORY and the F/P buttons.

“PRESET SORT” will appear on the display and sorting will be done.

To move back and forth between the

characters, press the TUNING / buttons.

Or the CH+ or CH– on the remote.

Note:

• Unused columns should be filled by entering

blanks.

6. To save the name, press the MEMORY or the

ENTER button, press the MEMO button on

1. Press the F/P button to show the preset station on the display.

2. Select the desired preset station by pressing the TUNINGor buttons on the front panel.

CLEARING STORED PRESET STATIONS

You can remove preset stations from the memory using the following procedure.

NAME INPUT OF THE PRESET STATION.

This function allows the name of each preset channel to be entered using alphanumeric characters. Before name inputting, you need to store preset

the remote for more than 2 seconds.

Ten keypad

Press, press again, press again, etc.

1	A → B → C → 1 → A

(Using the remote control unit)

1. Press the TUNER button twice within two seconds on the remote.

2. Press the > button until PAGE4 is displayed

3. Press the P-SET+ (D4) or P-SET– (D5) button to tune in the deseired preset station.

2.3.

				TEST	CH.SEL
V SURROUND RECEIVER SR8400				1	2
				7.1CH	ATT
				4	5
				DISP	OSD
	CLEAR	MEMORY	TUNING	7	8
				CLEAR	0
ENTER
TV	DVD	VCR1	DSS/VCR2 AUX1	CD-R

PHONES

SURR

SPK-AB

SLEEP

MEMO

stations with the preset memory operation.

4.	5. 6.	4.	2. 5. 6.		5.
	SELECTOR
		CLEARCLEAR	TUNINGTUNINGF/P	MODE	DOWN	UP
	TV	DVDVCR1	TAPE	CD	TUNER

AUX1 INPUT

2	D → E → F → 2 → D

3	G → H → I → 3 → G

4	J → K → L → 4 → J

5	M → N → O → 5 → M

6	P → Q → R → 6 → P

7	S → T → U → 7 → S

8	V → W → X → 8 → V

Or enter the preset station number with the numeric buttons.

DVD

VCR

DSS

1. Recall the preset number to be cleared with the method described in “Recalling” a preset station.

2. Press the MEMORY button on the front panel or press the MEMO button on the remote.

3. The stored preset number blinks in the display for 5 seconds. While blinking, press the CLEAR button on the front panel or the remote.

CHVOL

PREV	8	MUTE
7	8	9

CLEAR0 MEMOMEMO

5.

SOURCE

PAGE 2

D1D1

D2D2

D5D5

4.

9	Y → Z → space → 9 → Y

0– → + → / → 0

Marantz manual 2 5, English, Using the remote control unit, Using the SR8400

Models: SR8400

2.

4.

2. 5. 6.

5.

4.